MAH3000AKW Maytag Washer - Instructions

Removed tub replaced bearings. Put in new seal. Be aware drawing on instruction shows seal cup instaled from wrong side of seal. Other wise went well. Got bearings from McMaster Carr.

Being a seventy five year old man I was reluctant to taking on this job but after getting prices for the repair or replacing the machine I cringed and trying to save some money I took on this job.Got all the information I could find on line I got started.Taking machine apart was easy and remembering to keep parts separated is something I learned from my mechanical back round is a must.Pictures also help.Taking out spinner drum easy.Bearings a nightmare If you don't have a bearing removal tool.Front bearing had to be cut out with a dremel tool and zip wheel being careful not to destroy the race.Removed spindel from spinner drum as I could see that for me to put shaft in hole would have been a problem.Put new improved seal in.Easy part.Reassembled. Springs and clips hard.Washing again and quiet.Wife happy four days later.Old guy sore.All done with outer tub in machine.Estimated savings Big,Big,Big.Getting big steak dinner and big kiss.

Thanks to Partselect's accurate parts' lists, and installation video, along with others' posted installation trials, gained confidence to attack problem on my own (coupled with repair (or should I say, "replace")men's advise to trash machine). Bearings had basically disintegrated, causing inner tube to be out-of-alignment, and rub against outer tube. Would just like to add to what others' contributed, that I found Plumber's Tub Drain tool to work very well at knocking-out larger front bearing (was perfect fit to ID of bearing). Had to Dremel cut out rear bearing, but quite accessible from rear of machine. Otherwise, alot of cleaning from 13yrs. of useage. Thanks for everyone's assistance!

I referenced the enclosed instructions, and U tube videos, along with gasket I also changed the bearings for about $40. From local grainger, it seems to have solved problem, thanks for quick shipping,

Following the information on the web it simplified this repair a great deal. Disassembled the front of the machine, then pulled it out from the wall, removed the rear panel. Removed the belt & pulley and knocked the shaft loose from bearings. Removed the tub and using the brass bar drove the rear bearing out first then removed the seal and front bearing. The seal has to come out first so the plastic spacer can be removed, used the brass bar from the rear of machine to drive front bearing out. Cleaned up all parts and reassemblied. Replaced the motor isolators and drive belt with new since I was in the machine that far. Removed the soap & bleach tray and cleaned up all those parts. re-assembled and washed a load of rags to test machine. Sounded like a new machine. Sourced the new bearings from a bearing supplier they are 6200 Series bearings, Rear 6206-2RS; Front - 6207-2RS. Had I not made this repair I would have been buying a new washer & dryer so this job for a little over a hundred bucks saved me thousands! Thanks to PARTSELECT for all this information!!

Repair was simpl, took about 3 1/2 hours +. Used on line video for dismantal information & reassembling. Hammered out old bearings and seals. Installed them with big bolt and old bearings, I used the old bearings as pushing tools for new bearings. The large bolt and nut pulled the bearings in to place at the same time. Installed seal and reassembled machine. I moved from Jester to King at home.

I had pretty much the same experience as others. Difficult parts were 1) removing the inner tub, I used the blunt side of an axe with a 4x4 after several hammers would budge it. 2) removing the old bearing, like others I had to cut them out using a Dremmel with a steel cutting disk from Home Depot ($15) Wear eye protection as sparks are flying! Cut out the inner race and the bearing fell out, then cut V notches in the outer race, trying not to cut into the bearing seats on the tub although I did have a couple small cuts, then hammered it out from opposite side. Installed the new beaings and metal sleave between (what is the sleave for?). I tapped both bearing up against the seat shoulder but with the sleave in between there's not enough room and the new bearings turned real hard as the sleave is binding them. (Minor panic). A couple taps with hammer and chisel on the inner bearing from opposite side to push it out created enough room and the bearings turned real easy. Suggestion; plug the drain opening in the bottom of the outer tub with a towel or sponge to prevent pieces of the old bearing from falling in there. I saw one ball roll down in drain, so I tipped the machine on its side and several balls washed out plus pieces of the old bearing. I had a towel laying over the top but that wasn't enough, needs to be stuffed down in the opening. Re-assembly was easy and the machine runs perfect. The wife is very impressed. Total investment approx $85 (kit, bearings and cutting disk) plus about 8-10 hours vs $800 repair or new machine.

Accessing the bearing housing was quite easy and the PartSelect videos were quite informative. Upon removing the lip seal the bearings obviously needed to be replaced. The bearings needed to be purchased from a local supplier and we used Grainger #6L028 (rear bearing) and #6L029 (front bearing). We needed to apply a generous amount of Liquid Wrench and used a long drive punch pin and a 3-jaw pilot bearing puller to remove the bearings. After removing the rear bearing we broked the puller on the front bearing, but were able to remove with the punch pin with the access created at the rear of the drum. Reinstalling the bearings was text book, we used a long bolt with large washers to pull the front and rear bearings together, with the spacer inserted between them.

I was sick when I heard the noise from our washer. I looked online at new ones and found out it was going to cost between $1000 to $1500 to replace it. While looking online I found the PartSelect site. Unbelievable! I put in the model #, read the posts, ordered the parts and within a few days they were in. Using the video and the posted instructions I took it apart and replaced the bearings and seals. The whole thing took about 3 hours and we were back to washing clothes. Total repair costs were about $160 to $180. Compared to the price of a new washer, you guys saved the day.

Removed front panels, lifted top to open position, removed back cover, removed drive belt, drum pulley, removed rear bearing snap ring, removed seal clips, removed 3 baffels then the 3 mount bolts. Pulled out spinner support and the inner drum. Removed the rear bearing #6206LL with brass drift rod and heavy hammer (came out with little effort. The front bearing #6207LL I soaked with penatrating oil overnight (this bearing was making all the noise as after 11 years water finally got to it) The next morning I had little trouble removing it with the brass rod and hammer, taking my time to work my way around driving it out. After cleaning everything up, assembly was the reverse, carefully driving in the new bearings. The new lip seal was the most difficult getting started without going in crooked. Time spent was a good 8 hours (it would have been more if the outer drum was removed) and the cost of everything was $167.09. Thanks to Part Select, the spinner support assy came the very next day. The two bearings came from Bearing Supply & Depot Inc. The washer operates like new!! Very Quiet!!

It was very easy...we ordered the part and it only took a day and a half and it was here.

Removed 4 screws and door, lowered and removed front panel,removed screws holding locking tabs for the machine top, removed the four screws holding soap reservoir, lifted the top. Located under the lid and above the doorway I pulled out the wax motor retaineing clip with pliers and the wax motor, used pliers to remove the wire connectors, hooked them up to the new part and reassembled.

When I looked up the part number, there was an installation video on the same page. I ordered the part then and there, and once it arrived, I put the iPad right on top of the machine and paused the video whenever I was doing the steps. It was TOO EASY!

I read the reviews from others fixing this same part, it didn't seem to difficult. It was not even hard at all. I installed the part and my washer does not leak at all. My Neptunes are old so I am very sure I will come back to buy parts here. I did install the hinges backwards at first, the didnt close so I had to take an extra five minutes to turn them around.

Replaced parts then the door wouldn't unlock, so we called a repair man and he's replacing the control board and the wireing harness, it cost 394.85 but the machine is in good shape so it was cheaper than buying a new washer and dryer, because I want them to match & the dryers only 7 years old.