MAH3000AKW Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Vicente from Newnan, GA
- Parts Used:
- 12002039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Motor won't run.
Followed the troubleshooting procedure that came with the
washer.Found problem,(with a little help from my experience
in electronics). Order motor and control board kit.
Followed the easy instructions that came with parts and
had it working in no time!!!!
Good job PartSelect !!!!
washer.Found problem,(with a little help from my experience
in electronics). Order motor and control board kit.
Followed the easy instructions that came with parts and
had it working in no time!!!!
Good job PartSelect !!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Painesville, OH
- Parts Used:
- 12002039
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Motor/board , ran erraticly-stopped midstream
Had to move all the concoctions my wife uses on my greasy work clothes [ purple power, dawn dishwash soap,lestoil, etc..] Removed front , removed back panel..Replaced board then motor..Replaced belt while I was in there.I had already changed out the tub bearing assembly earlier..Quite a complex machine when you get in that deep..Runs like new...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Avon, CT
- Parts Used:
- 12002533
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Mashine leak was quickly diagnosed as rip in boot
The machine comes quickest appart with a cordless screwgun and a #2 Phillips.
To unhook the wire with spring it is easiest to use a needle nose plier and make a hook from a coat hanger or use a paint can opener.
Pay attention when yo line up the boot with the flange in the back, that the rectagular protrusions line up with the holes in the flange. You may have to stretch the boot a bit and push it all the way in with a dull tool.
Get someone to help you put the wire back on if you want to do it fast and easy. Otherwise hook it on the spring and get the pliers on the loop on the other side and pull it together, torquing the wire back so that it does not make the boot slip fo the flange.
Done
To unhook the wire with spring it is easiest to use a needle nose plier and make a hook from a coat hanger or use a paint can opener.
Pay attention when yo line up the boot with the flange in the back, that the rectagular protrusions line up with the holes in the flange. You may have to stretch the boot a bit and push it all the way in with a dull tool.
Get someone to help you put the wire back on if you want to do it fast and easy. Otherwise hook it on the spring and get the pliers on the loop on the other side and pull it together, torquing the wire back so that it does not make the boot slip fo the flange.
Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gordon from indianapolis, IN
- Parts Used:
- WP22003059
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
change stuck in drain pump, damaged the motor
just replaces the pump , the replacement pump was a little different than OE , mounting bracket different but was able to remove housing and bracket from broke pump and put on new pump , all works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charnell from Tacoma, WA
- Parts Used:
- WP22003059
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
It went like butter
it's best to pull off the back of washer then it is too go through the front thats my only hint
Was this instruction helpful to you?
Thank you for voting!
One of the drum baffle's boke from it's mount
Removed old broken plastic grommet's and installed two new plastic grommet's. Attached new baffle using old screws. Used a short piece of picture frame wire to install the two new grommets by fishing them into place with out removing the washer drum.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GREGORY from HALIFAX, PA
- Parts Used:
- 12002533
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
I found water on the floor beneath the washer. Further inspection revealed the door boot was torn.
I removed the screws around the front door. Then removed the front face. I removed the bolts holding the top down at front top corners. I removed the detergent dispensor. Next I removed the spring and hold down cable. I then pulled out the old boot. I then, with the help of my son, pulled the new boot around the drum. Then attached the cable and spring. Next pushed the boot into the front retainer. I then put the dispenser in and the front back on. Good as new. It was not hard as long as you have someone to help with pushing the boot around.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Huntington Sta., NY
- Parts Used:
- 22003856
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Motor did not have the ability to rotate washing machine drum.
Removed old motor installed new motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benny from Shelbiana, KY
- Parts Used:
- WP22003059
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Would not spin the water out of machine.
The pump motor was making quite a chattering noise about 2 months before it totally quit, Ordered part it was shipped very fast.(before the next wash day). Took the back off remove 2 hoses and 2 wires installed new motor. Very easy job and it is working very quite and great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Sunbury, PA
- Parts Used:
- WP22003059
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Would not pump out water
I have a new Matag repairman, my husband. He took the front panel off by removing the screws. Then removed the balance on the drum and found the pump. Put the new one on and put everything back and my washer runs better than it has in a long time. Saved us a service call and hourly rate for a service man that couldn't come for 4 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilson from Logansport, IN
- Parts Used:
- WP22003059
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The pump would not empty the washer.
I had taken the back off the washer already. The pump was connected to an incoming fitting and the out going fitting with hose clamps. Removed the hose and hose clamps from the old pump, connected the hose and hose clamps to the new pump, reconnected the wiring and that was about it. The pump was mounted to the bottom panel of the washer by simply plastic plugs requiring no tools. It was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from PUYALLUP, WA
- Parts Used:
- WP22002077, 12002533, 12002022
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Replace front and rear bearings and bellows
Of course I looked at you tube to get the instructions on how best to do the job. It was very helpful. Getting the front bearing out was the major issue. It was so corroded that I could not get it out with a hammer and punch. I had to build a bearing puller which I copied from the you tube video out of a 3" schedule 40 pipe. After that the repair went very smoothly. Putting on the bellows cable and spring assembly took two of us. Also putting the clips that held the inside drum on took two of us. One of us used channel loks to squeeze the two drums together while the other installed the clip. I had trouble identifying the tube seal part number. I phoned for help and the customer service person was very helpful and ordered me the correct part. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert A. from Warwick, NY
- Parts Used:
- 12002039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Motor had an open in winding
1) Removed machine front by removing four (4) screws. 2) Removed rear access panel. 3) Replaced antiquated motor controller with upgade revision; basically unplug and plug 4) replaced motor and 5) closed up unit. Whole job took about an hour with half the time spent moving the unit to work oo.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Anchorage, AK
- Parts Used:
- WP22003262, WP22003059
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Machine had been making a howling noise during rinse cycles for several weeks and then suddenly stopped draining.
On-line trouble shooting sites indicated that drain pump was likely culprit. Disconnected pump from hoses and removed and replaced pump. Tub to pump hose had considerable scale in it, so replaced that too. Repair was made easier by removing both the front and back panels of the washer to get best access to hose clamps and pump.
Was this instruction helpful to you?
Thank you for voting!
Washer was so loud in the spinning cycle it sounded like a jet was taking off
We took the washer completely apart. Replaced the bearings, pulley and
belt. We decided to replace anything that involved the spinning cycle while we had it all apart.
It was well worth the time and effort we put into it. It works like a chime
and is very quiet . Silence is golden ! Hopefully it will work another 18 years.
belt. We decided to replace anything that involved the spinning cycle while we had it all apart.
It was well worth the time and effort we put into it. It works like a chime
and is very quiet . Silence is golden ! Hopefully it will work another 18 years.
Was this instruction helpful to you?
Thank you for voting!