MAH14PNAWW Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- victor from el paso, TX
- Parts Used:
- 12002022
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Machine shook violently durring spin cycle
I referenced the enclosed instructions, and U tube videos, along with gasket I also changed the bearings for about $40. From local grainger, it seems to have solved problem, thanks for quick shipping,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Lincoln city, OR
- Parts Used:
- 12002533
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Stinky Neptune front door seal-Mildew
The replacement was not complicated. It took me more time because the details are not in the videos and I had to do it twice because I didn't get the seal on correctly the first time. I used the Neptune videos available on you tube for the basics. Use the "inspecting front door lock wax motor" video for a start, but be sure to take off the top front crosspiece also for easier access to the spring that tensions the seal retainer cable. You don't have to disconnect any wires, just lay the door lock assembly gently to the left of the washer. The old seal comes off very easily, using the front loader door seal video. My washer was an early one without the drain tube so I had to get the drain tube and clamps separately and drill out the tub nipple to the left below the seal. I used the biggest drill bit I had that fit inside the nipple. The tub is plastic and very easy to drill. Most of the plastic shavings will come out toward you if you drill slowly and don't push too hard on the drill. I also used my shop vac to try and get out any other shavings. I used dish washing liquid as a lubricant to help put the seal on and used too much. It doesn't take very much. The spring that tightens the inner seal clamp/cable was very hard to attach and it did require two locking pliers [vise-grips] and quite a lot of effort. You have to hook one end of the spring to the cable that wraps around the seal, hold the other end of the cable with locking pliers, the free end of the spring with locking pliers, and stretch the spring to hook it to the free end of the cable. There are some other methods described in various forums and one of them might work better for you. When I was an auto mechanic we had a special tool that helped attach springs like this on drum brakes. I was sure wishing that tool was still in my tool chest but it was not. This was the most difficult part for me, getting the cable and spring all in place and stretching the spring without dislodging the seal and having to start all over.I didn't get the seal aligned correctly the first time and had to do it over after putting ever thing back together and washing a load of clothes. I could have avoided that by carefully inspecting the seal before I put everything together. When you put it back together the end of that red or green nylon line that looks like weed eater line goes under the soap/bleach dispenser bezel on the top so you can manually open the door if the wax motor goes bad and it won't unlock.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- scott from lafayette, CO
- Parts Used:
- WP22002119
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Whenever the timer hit the rinse cycle, my breaker would trip
First I took off the door and the front of the washing machine. Then, took off the bracket of the soap dispensing bin from the top of the machine. Then lift up the top of the machine, and unscrew the bracket that holds the wax motots, label and pull wires, replace motors and wires and put back together. This is also a good time to clean and dust the interior of the machine. Before replacing, my motor smelled and looked burnt out, instead of paying $300 -$400 to have someone look at it, I investigated and I fixed it for around $30. I hope I get to inspire people to figure things out and save some cash!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ryan from Troy, OH
- Parts Used:
- WP22003059
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
washing machine leaked out the bottom.
diagnosed problem (hole in drainage pump). unplugged, took service panel off rear, removed hoses, twisted pump counter clockwise. dropped new pump in, made connections, and it was good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Phoenix, AZ
- Parts Used:
- 12002533
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washing machine bellow had developed some black mold over time that could not be removed and needed replacement.
Video repair instructions on the Parts Select site was right on and made the repair very easy. I took a little longer in my repair as I cleaned each piece I took off to make sure there was no dirt/lint/rust/mold remaining. The only difficult part was putting the spring back in place, this took a couple of tries. Other than that, relatively easy to replace and would recommend that anyone with any handyman skill to do this repair/replacement themselves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Wilsonville, OR
- Parts Used:
- 22003083
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Inner door liner had a hole in the bottom causing water to leak out the door
We read the instructions on the website which were very useful. We have a Maytag front loader. The instructions and pictures which came with the part are written to look like the hardware in the door and the door latch spring etc. is attached to the outer door. I realize this part fits multiple brands but instructions could clearly state that you have to remove all of the hardware from the inner door liner that you are replacing and reassemble it to the new inner door liner. It is really important to take pictures of how the door latch and spring are attached as this took the most time putting back on the new door liner. Our washer is older and did not have a vent tube and now has one. In the end, everything was correctly reassembled and we no longer have a leaky door. Shipping was very prompt and we're pleased with the part and repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Fremont, CA
- Parts Used:
- 22003721, WP22003718, 22003717, WP22003716, WP22003715, W10859556, WP22002162, WP22002119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Door would not lock, no door locked light, would not start wash cycle
Removed front panel and door, lifted top cover to access door lock. To remove the wax motor, you need to remove the Door Lock/Spin enable switch. Important note, there are two switches so to completely rebuild the door lock, you need get two of the Door Lock/Spin Enable switches. Same part/part number, one is for the door lock and the other for the Spin enable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emil from Bonney Lake, WA
- Parts Used:
- 12002022
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Getting a slight "thunk" or "chirp" when the drum shifts direction
I bought the new Lip Seal Kit thinking that the sound I was hearing had to do with it sticking inside the drum at the end a rotation in either direction. We had replaced the outer drum a few years back when the bearings went. Believe me, you will know when your bearings are going. It sounds like you are in the same room with a jet engine. I knew this sound was not from the bearings. I had the washer apart in about fifteen minutes...and yes, I am a 125 lb. female...so ladies, it is not an impossible task. I have taken that washer apart enough times before that it is no big deal. Just make a mental note as to how it goes back together....if all else fails one can look at diagrams online. My husband just stood there and said "nice job honey". After I got the old seals out and the parts cleaned up, I turned the bearings to make sure they sounded smooth. A-okay. I installed the new seal and smoothed molycote on the spider shaft; replaced the drum, front panels, etc; tightened the pulley with a torque wrench, belt on, etc. and.....turned on the washer. The sound is still there. Sooooo, I am fairly confident that it comes down to the belt and the motor isolators...mostly the isolators...belt is pretty secure. I am changing those tomorrow. Found someone on youtube with the same problem...only far worse...and a response posted said it probably was due to the isolators and belt. Our seal wasn't too fried, but I guess that it isn't a bad thing that I changed it anyway since it has been a few years and they do fail resulting in bearing damage. Better to catch it now. As for whether my machine is worth fixing at its age, I went shopping while this was going on and I don't trust anything out there to not have a multitude of problems. At least with my current model...that still looks like new btw...I don't have a learning curve to deal with on how to take it apart. And a great big shout out to my father who taught me how to dig in my heels and get my hands greasy!! Update: Replacing the motor isolators did the trick. Put on a new belt too as long as I had the back panel off again. Running like a champ!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Winston Salem, NC
- Parts Used:
- 12002533
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Moldy Bellow
I watched the provided video that EXCELLENTLY showed the replacement of the part. Then I was able to complete the task with no trouble at all
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Crawford, CO
- Parts Used:
- WP22002119
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Washer would not run, seemed like the wax motor was the most common cause.
Watched the video, worked just like shown so as quick as you can take out 8 screws you can make the repair. Turned out it was the MCB but maybe this part (wax motor) Will save a main control board failure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Oak Ridge, TN
- Parts Used:
- 12001788
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench set
washer smelled hot on spin cycle
Replaced the belt and motor isolators. Watching your video made it very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- greg from ozone park, NY
- Parts Used:
- WP22003716, WP22002162
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
no door lock light
remove door with Phillips remove front panel nut driver remove soap tray lid and lift up top Phillips test small contactors for continuity and replace removed locking sprocket and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Pleasant Hill, CA
- Parts Used:
- WP22003059
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Water would not pump completely out
Remove the back panel (4 screws). Use screw driver to loosen the bands. I had to tilt the washer up on a block to "twist" the part free. Once you see the bottom of the washer, you can see how the pump attaches and how to free it from the mount. The hardest part of the job was trying to get the hoses back on using one hand. That was a hard task. I used the shop vac to suck up the water that came pouring out of the drum once I loosened the bands. Not a hard repair. Unfortunately this did not fix my issue, but I wasn't going to go through hooking the old pump back up. (Was the far more expensive timing board that was faulty)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Mayville, MI
- Parts Used:
- 12002533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
water leaking in the front of the machine
My 16 yr old son replaced the door boot. He said it was very easy although the wire was alittle tricky. But all in all it was very easy for him. Saved me alot of money.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norma from Donald, OR
- Parts Used:
- WP22002798
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door sagging
The service representative knew exactly what was needed from the description of the problem that was given to her. The hinges were received within a few days. The door was removed and the hinges were replaced and it does not sag anymore. Thank you for your great service.
Was this instruction helpful to you?
Thank you for voting!