MAT12PRSAW Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer would not agitate.
Since my missus keeps her appliances like new, it behoves us to buy something of good quality when new. We did that. Now, after almost 20 years, the washer complained it needed new belts, which I complied. Tilted it up against the wall after pulling power cord. Removed both belts and replaced. Adjusted pump belt by loosening pump and then retightening. This is easy to get to by removing front (removing 2 philips screws). Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from HOMESTEAD, FL
- Parts Used:
- 12112425
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Worn belts
Slipped on belts no tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from MOUNTAIN BRK, AL
- Parts Used:
- WP212716
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Washer is 27 years old. The washer lid bumpers were just worn out with age. It has been in constant use all these years raising 4 children with no other service or repairs. It has a matching dryer with the same track record. What a testament!
Removed the front panel with a screw driver, removed the old bumpers with a pair of pliers, replaced the bumpers and replaced the panel. All was very simple and took no time. The video on your website was most helpful. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- petrose from blaine circlepine, MN
- Parts Used:
- WP22001969
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no problem
befor start i make sure whether i can repair or not.then i order the part which is fit with what i wont to repair.by checking siriel number . then repairng is very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Toni from Glendale, AZ
- Parts Used:
- WP6-2022030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
pump was leaking water
Unplug washer and shut off water valves. Remove water hoses from the faucets and caught the water in the hoses in a bucket. I removed the drain hose from the back of the washer and caught the water in the bucket. Remove front panel by removing 2-screws at bottom and tilting it out to come off. Disconnected the hoses to the pump and caught most of the water in the bucket.. An old towel stuffed under the bottom pan of the washer, under the pump hole caught most of the rest of the water. Tip the washer on its back and removed the belt coming from the motor. Removed 3-screws that hold the pump on and angled the pulley end through the hole in the bottom of the washer. I just reversed the procedure to install the new pump and everything else. I would have replaced the hoses and belts, but I had just done that about a couple of years ago, when I replaced the connector at the top back of the washer for the hose from the pump and hose to the drain in the wall, that had a crack in it and was leaking.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Saint Louis, MO
- Parts Used:
- 12001908
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
the device that indicates the lid is open/closed malfunctioned due to a forceful slam
After removing defective part and replacing it with the new part, no thanks to skimpy instructions that came with it. We discovered that it wasn't the lid switch assembly but, the hinges and washers? and the little plastic piece that pushes the plunger so we had to order those. Surprised they didnt' come today. The first order came almost the next day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell B from AUBURN, CA
- Parts Used:
- 12112425
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Belts did,nt work .Need clutch assm.
Install belts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from BERKELEY, IL
- Parts Used:
- WP6-2022030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Wet close after spin cycle
I replaced the 3 screws because they were rusty. Then I replaced the Drain pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from LAKE CYRSTAL, MN
- Parts Used:
- WP6-2022030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Tub Did Not Drain
Received drain pump by fed ex, put it on in 15 minutes. . . My wife was very happy again. . . .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michell from TOOMSUBA, MS
- Parts Used:
- WP211726
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing hinge lid ball
Used duct tape as the video provided instructed and also to hold second hinge lid ball in place. Firmly pushed down on the lid until it easily popped in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hugh from canton, GA
- Parts Used:
- 12001908
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
mother dropped the lid on her machine breaking switch
unpluged the switch pluged other switch in not even worth a atta boy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Hartsville, PA
- Parts Used:
- 12001908
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
machine went off balance violently, causing lid switch tom fail
diagnosed problem by reading parts select symptom chaser. ordered part and received it in two days. It was a snap to install, simply reversed removal. had machine up and running in 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Petal, MS
- Parts Used:
- 12001908
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Intermittant operation
Removed 5 screws to remove console rear panel. Removed the old switch and plunger and installed the new ones. Worked good last long time.
Was this instruction helpful to you?
Thank you for voting!
Would not spin with load
Received wrong springs for my model had too use combo old spring with the two new (too long) springs to get the tension on the belts. For now it working. Did not contact you due shipping took so long and two delay date change by FedEx ground. I didn't want to go thru another delivery nightmare. Thanks for the time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from BRIDGEPORT, CT
- Parts Used:
- WP6-2022030, 12112425
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Leaking pump
Tilt the washer sideways. Remove belts,Remove front panel, loosen two hoses, loosen three small nuts. Take out old pump and install new new pump vise versa. Video provided by partselect very helpful.
Was this instruction helpful to you?
Thank you for voting!