MAT25CSAGW Maytag Washer - Instructions

Frist remover the two screws from washer front. The ones that are about 5 inches from the floor. Pulled front cover toward me and removed. The hose was right in the front that was cracked. It was held on by two hose clamps. I just removed the old and put in the new. No more water on the floor. Shipping was fast for the hose too. They said that if they recieved the order by 3pm it would be shipped the same day. I order at 3:01pm Sat. recieved Tuesday.

Removed front, loosened top & tilted up. Placed tub top assuring it would not rub inner basket. Placed clamp on Ridge & gasket & tightened. Reassembled & started washing.

Actually, the loud noise would happen only when valve shuts down water flow after filling up the washer (when water flow stops and washing cycle begins).
Replacement part was almost exactly the same. I did not need little transparent hose piece (used clamp that was already there). I used a combination of repair tips others already listed here: unplug washer's electricity cord 1st ( turn water off ; unhook hoses from back of washer(...); remove top screw off of inlet valve's back panel first and push up/out the bottom; unscrew valve off of panel; without yanking things around much, note exact connections of cables & hose(s); replace with new part, and put back on in reverse order.
One important note: the new part's screw holes were ungrooved but not too hard to slowly work in the screws because of the soft alloy. Be patient, good luck!
PartSelect: Great website/catalog, great service.

Since the washer is 28 years old, my first impulse was to rush out and buy a new one. However, I'm a DYI'er and I figured what do I have to loose by taking the front panel off (I had seen this done by the Maytag Repairman) and checking things out. After removing the two screws located near the bottom front of the panel, I pulled out on the bottom and the panel easily came off. I couldn't see any evidence of leaking water so I thought, "what would the Maytag Man do next". I figured "he'd run through a cycle to see if he could find the leak" so that's what I did. Sure enough, as soon as the spin and drain cycle came on, the source of the leak became apparent. There is a slight vibration during the spin which caused the hose to fail.

I then got on my computer, Googles "repair parts for Maytag Washer" and found Parts Select.Com. I was surprised (to say the least) to find the part I needed in stock. I place my order on Sunday morning and the part was delivered the following Wednesday afternoon. I installed the hose and replaced the front panel and was washing a load of jeans within 20 minutes.

I appreciate the service provided by Parts Select and will be ordering again when the need arises.

Tom Nelson
Fort Worth, TX

I turned the water off, detached the hoses and unscrewed the water inlet valve. I unhocked the wires and reattached the wires in the correct sequence on the water inlet valve. Done in 15 minutes.

Turn water off, removed water hoses. removed plug from elec. outlet.Then remove water inlet valve.very simple.

Found noise to be belt slapping the base sheet metal, from being too loose. Belt was loose because the drive pulley was worn and one side of pulley was loose! Used allen wrench to loosen the pulley set screw, and pryed off the old pulley. Replace d with new pulley and new belts. Works and sounds like new!

Lets just say thank god for part select!!!! # 1 By far. This was a one two three job.

Removed the damaged legs, replaced with parts from this site and leveled the washer .

After turning the water off and unplugging the machine, I took the front panel off the washing machine. I then slipped the belt off the pump sprocket. The pump was right in the front and easy to remove. All I needed was a screwdriver, for the hose clamps, and a 5/16" socket to remove the old pump. I then installed the new pump, with the existing screws, re-attached the 2 hoses, slipped the belt back on, and popped the front panel back into place. The new pump works great and the leak is gone. The whole job onlt took about 30 minutes.

Washer originally purchased from Sears. Called Sears for repair. $65.00 to show up. Diagnosed the problem as a Bad belt and pump. Asked for approx. $250 to repair. I declined and ordered a belt and pump from PartSelect.com for half the cost. Took 10-15 minutes to install. Turned the washer on and put it through a drain cycle, it leaked all over the floor. Turns out the only problem was a cracked Outer Tub to Pump Hose. It took about 10 minutes to install. Whala, no leak. Now while I purchased an un-needed pump and belt from PartSelect.com, not their problem. Even though I purchased two items that were not required, the cost was still half of what Sears wanted to charge me for a repair that would not have fixed the problem. I will certainly continue to use and recommend PartSelect.com.

Instead of replacing one damage hose, i decided to replace the whole piece. the second hose was old and i figure ill just take care of one problem now and prevent a future problem. it was as simple and quick, save me some money from hiring a repair man. it was also a learning experience.

Did repair as instructed by video, I'm 74 years old if I can do it anybody can!

You will need 2 hose clamps not sold as maytag parts.

Remove front washer panel screws.

Remove bolts holding front of top to side panels

Remove hose clamp from front hose to injector sleeve.

Twist fill hose ccw 90 degrees at tub fitting to remove.

Clean corrosion at tub attachment point wuth wire brush.

Paint bare metal to seal. Allow to thoroughly dry.

Remove injector sleeve and injector hose.

Trim new injector hose to match length of removed hose (I cut off abt 4 inches)

Install injector hose and plastic sleeve. Ensure clocking is correct on hose.

Install gasket on fill hose fitting.

Insert fitting into tub. Rotate 90 deg CW to latch.

Install gear clamps loosely on fill tube.

Attach fill tube to fill fitting and injector sleeve.

Slide clamps onto tube ends ensuring clamp clocking provides access and clears tub top..

Test tub fill to ensure injector works without leaks

Cleaned the cavities. Lubed them with olive oil. Inserted one ball on left side, while holding tension against that side to hold the ball in the lid and top indentations. Applied olive oil to right hand side indentation, and placed the new ball into lid indentation. Put lid down into closure cavity with ball, and with lid vertical, began pushing it rearward so as toslightly spring metal lid rolled edge and top metal away from one another UNTIL the new ball snapped into the hinge indentation in the machine cover. Done.