MAV7501EWW Maytag Washer - Instructions

I didn’t have special tool for brake but punch and hammer worked. Seal was easy to replace. Several videos online to show you how. It wasn’t worth it to tear apart the transmission and buy more parts/seals (if they were even available). But I didn’t know how much oil was in it. I drilled a hole in the side to somewhat check level and added 80-90 gear oil. It was almost empty and added almost a quart. Used a self taping screw/bolt with gasket sealer to plug the hole. I got 34 yrs out of this washer. If it fails, oh well. Just hate to buy a new one that only last 10yrs if im lucky.

Simple remove and replace. Plastic cam and hinges simply snap out, replacement parts snap right back in. Needle nose pliers were helpful to remove broken lid cam. With hinges and lid removed, took advantage of great opportunity to clean lid and and top of washer.

I opened up the top of the washer which exposed the tub, I took the top ring off the tub and under in side of the ring is the seal. Took the old one out and put the new one in. The old seal was completely wore out.
It was real easy.
Finding the part is usually the hardest part, but thanks to Parts Select finding the part was the easiest part of the repair.

Removed inspection panel on rear of washer. Pump right there. Removed inlet and outlet hoses with pliers on squeeze clamps. Three 3/8" size self tapping screws were removed and old pump came right out. Reversed process with new pump from this site that fit perfectly. New pump was an upgrade factory part that mounted inside washer without a mounting plate as the old one did.

Replace the motor in 25 minutes, my repair guy said it was not worth the time , I got this motor for less than $150. And save my self over $600.00, this was incredible.

I removed the screws to loosen the belt, took off the old belt and put on the new belt. Tightened it up and has been working ever since.

Thank you, Lester

you guys ship faster than anyone else. One day I order the part and a day or two later there it is. :)

Diconnected water lines, layed washer on its side, spun pulleys and pulled belt off at the same time, put the belt on in the same way. VERY simple

Pulled wahser away from wall, unpluged, removed screws from rear access panel, removed hoses from water pump, used towell to absorb excess water still in pump and hoses, removed drive belt, removed screws securing pump, removed old pump replaced it with new pump, cussed a little when replacing hoses, repeated steps in reverse order, checked for leaks.

Removed timer knob. Removed 4 screws that fastened front panel. Opened front panel to access timer module. Unplugged connector & removed sinlge mounting screw. Slid timed out and replaced with new unit. Reversed process to re-assemble.

Only problem was the 1st timed module arrived damaged. Customed service rep apologized & quickly ordered a new unit, which I received in 3 days.

Parts look up was simple. part was priced right. part received in a timely manner and was as advertised. installation was quick and painless.

Took the washer outside, turned the washer on its side to expose the bottom panel. Removed the old water pump (three screws and two hoses. Replaced with new water pump and connected all fittings. Real easy to do. Washer runs great now.

take a butter knife and pop the clips loose on the front between the lid and the front take the two screws loose on the front in each corner remove the front cover and you will see the hose take the clamps off and replace the hose

I just needed to replace a knob because the original, (plastic) broke. What was great was how soon I received my order, just a matter of a couple of days. I wish I had ordered several as both my washer and dryer have the same ones (five in total) and now another one as broken! I think I will order three or four move.

Took a putty knife and raised the top,then took two bolts out, then pulled front panel off. Took hose off from the tub to the pump,and put the new one on. It's working fine.

I knew it was the belt because of all the noise it was making. I ordered the belt and it arrived real fast. I pulled the washer away from the wall and tipped it back at about a 45 degree angle against the wall so I could get under it. I propped it with a bucket. I then pulled the old belt off and spun the new one on. Real fast & easy.