MAV7260BWW Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Eleanor from PALATKA, FL
- Parts Used:
- 12002213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Washer was making a squeak during spin cycle & then just stopped spinning
I watched the video of the repair on this website and followed it. Was really easy & THANK GOD because this was my first repair. This has been a great machine and it looks like it will continue to be for a little while longer! Thanks for the video help and friendly navigation of your site!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from CONNEAUT, OH
- Parts Used:
- WP22003989
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Timer and timer knob were broken.
Watched video from on YouTube. Disasembled dryer by removing cap from timer knob. Pulling timer knob off the shaft. Removed three # 15 torx screws from the top of the dryer. Top panel rolled forward. Depressed plastic tab removed timer and unplugged wiring harness. Ordered parts from this site online. Parts arrived in 2 to 3 days. Parts were installed following reverse order from above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from MADISON, TN
- Parts Used:
- WP35-6780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Loud noise in spinning cycle
There is a small back panel about 14" square made to open for access to the drain pump. 3 screws for the back panel and 3 screws for the pump - Oh you do have to slip the belt off & back on, underneath the machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LEWIS from ROSWELL, GA
- Parts Used:
- WP22004333
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Water leaking into tub between used
Unplug electrical plug and shut off water supply. Putty knife to release latches at top left and right corners of flat top top where cloths go into washer. Take picture of wiring connections. Remove water diverter cover by unhooking snaps. Remove single screw holding water diverter. Remove single screw holding inlet valve and pull valve and water lines thru access hole. Disconnect wiring connectors and unscrew water supply lines. Reverse process to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- terry from erie, PA
- Parts Used:
- WP22004385, WP35-2328, WP22003483
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Seal Leaked
1 I opened the top of the washer found the top plastic rim piece broken due to the fact that it cracked while unbalanced one time. Which made it leak which ate away the rubber seal . The parts were here fast and they were the right ones. Great job and I will tell everyone about you thank you verry much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brena from Seaside, CA
- Parts Used:
- WP35-6780
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Busted Pump
We had a repair guy come in and he said fixing the pump would cost at least 250. I called my dad and he walked me through it over the phone. I took off the back of the washer, and laid the washer on it's side. I then had to take a break as I had flooded my kitchen. (Lay the washer at an angle.) The belt was taken off by the repair guy. I then undid the hoses, taking the clips off with pliers. Next I screwed the new pump in, and put the hoses back on. FInally I took the belt and stretched over the two small pullies, and then pulled it to the bottom of the big pullie and started spinning it until it wrapped itself all the way around. It wouldn't have taken over an hour but I had a baby who needed me ever couple of minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DWane from Waterford, PA
- Parts Used:
- WP21001598, WP21002026
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
noisy washer and shaking
disconected water lines unplug power and took drain pipe off, used putty knife to open top of washer and pulled off front removed pannel off back pannel, disconnected water level tube,using vise grips took off springs and pulled tb out used 5/16 socket to loosen screws just enough to pull snubber ring out replaced with new one reversed prosses in putting it back to geather
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ELMORE, OH
- Parts Used:
- WP22004469, WP21002026
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Washer Traveled and load would not be balanced. Washer would bang loudly.
Followed directions from video on your site. It was very helpful. The snubber ring fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Aplington, IA
- Parts Used:
- WP22003285
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
water on the floor
figured out how to open the top of the washer(Two small tabs I pushed in with a putty knife. Looked for the area it was leaking. Slide the hose clamps off with a pliers and pull out hose.
Put clamps on new hose, replace hose and slide clamps to ends to seal the connections
Put clamps on new hose, replace hose and slide clamps to ends to seal the connections
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Evans, WV
- Parts Used:
- WP22003804, WP22002754
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lid switch was broken when the lid slammed shut
The installation was extremely easy - videos sure helped. I would recommend this site for appliance parts - parts came ahead of schedule.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DOUG from COLDWATER, MI
- Parts Used:
- WP35-6780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
water pump froze during spin cycle
I took the washer into the garage, removed access panel from back. Spun drive belt. This located the trouble with the pump. I removed pump with three sheet metal screws and hose clamps. Upon delivery, I notice the two pumps were not identicle. I called Cust Serv. They assured the difference was ok. I installed the new pump with three screw, put the belt and panel and hoses on and ran a test load of my junk clothing. No trouble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- antony from ALTADENA, CA
- Parts Used:
- WP22002753, WP22002751, W10814230
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the wassher would shut down mid cycle. jamming a screwdriver in to force the lidback solved theproblem
I popped out the hinge pins, popped outthe busshings, popped out the cam. time less than 10 minutes, pressed in the limit cam, pressed in the bushings, pressed in the hinge pins. time about 5 minutes. the most important thing is my wife is extremely happy. I'm happy the parts fit perfectly.
also the parts arrived in 2 days.
also the parts arrived in 2 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from FREMONT, NE
- Parts Used:
- WP22003483
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
spinning slowly
This was a very easy fix.....roll belt off....roll new belt on....seemed to help not sure if it fixed problem....might try pulley and bearing kit next
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregg from Glendale, AZ
- Parts Used:
- WP35-6780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
drain pump failed
I first had to take the old part out to find out what the part number was. Then I went online and ordered the part. Once the part came in I attached to part and replaced the drive belt. I did not think it could be so easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from Lake Dallas, TX
- Parts Used:
- WP22003987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The control knob was broken
Removed it from the package and placed it on the washer.
Was this instruction helpful to you?
Thank you for voting!