3LMVWC100YW1 Maytag Washer - Instructions

Ordered the agitator repair kit and it came very fast.. Followed the instructions, the kit had all the parts needed.. Took around 30 minutes, but some of that was scraping the built up scale from the agitator itself, you might not have to do that.. Easy job.. Agitator now works like new.. Very Happy, and so is my wife, the kids looked and said, "Hey,my jeans go down to the bottom now, cool..!!"

I ordered a whole agitator repair kit. Had a few problems getting everything to line up right.Finally figured out what I needed to do and everything worked like it should.

Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.

I used a jack to lift the tub and unhooked the rods and replaced them. Works great.

followed video instruction that came with part. Previously watched youtube video (there are several, the low production videos are well worth viewing over the professional types). It was a breeze, other than the videos saying one person could do all four. When you get to the last rod, it is more difficult to lift the tub to insert the final rod in the round holder. I asked my wife for assistance.

I simply followed Steve's instructions on video. Very easy repair. Washer works great, no jumping or vibrating.

Removed agitator cover with small screwdriver. Removed bolt holding agitator with socket on 6" extender. Pulled agitator up and out. Replaced thrust spacer adding tiny amount of silicone grease. Replaced agitator directional cogs adding small amount of silicone grease. Note direction of cogs first or they will make a loud ratcheting noise. Reassemble. The drawing on this site is helpful.

I ordered the part and watched the installation video. It would have helped if I had watched the video all the way through at least once. Instead I paused and restarted it as I did the repair. As a result I had a hard time putting the agitator back together. Otherwise it was a fairly easy repair and my 20-year-old washer works great again!

1st watched the video, turned off the water supply, unplugged the elecrtcal cord, removed the rear top panel , screws with the nut driver , then slid the top forward about 1 inch & then lifted upwards to removed the lid assy, after taping the lid assy down so it wouldn't flip open. Then once lifted up, at the very back are 2 slots, which you can the set the top onto, then use the 2 s-hooks with a chain to support the lid assy from falling backwards and attach to the base assy.
Then you can move the tub assy away from where you need to work.in this case was replacing the upper plastic suspension rod supports, then push upwards the socket , drop in the new one, pull of on the rod assy, and hook it into the ball and drop bach into the suppprt , was able to do all 4 in no time. Then unkook and reattach all, screws, plug back in, turn on the water. And we were good to go.
All For less than $20.

I removed the agitator top cap first. I reached inside and removed plastic cap. I then removed the 7/16 bolt inside the agitator and lifted it out of the machine. I put my foot on the bottom part of the agitator and pulled the top part off. I removed the plastic bushing in the bottom part and then removed the plastic bushing with the dog ears and the bolt. I used some appliance grease on the bushing on the bottom part and slid the top part of the agitator back in place and replaced the 7/16 bolt. It worked like a charm. My wife says I'm her hero. Thanks for making it so easy.

Removed top agitator bolt lifted agitator out and replaced ring and geared dogs. replaced Agitator top swirl vanes. It would have been nice if the kit included agitator grease and a new bolt and washer.

Removed old agitator and determined teeth in center were worn down. Purchased new upper agitator assembly and repair kit. It now works like a new washer. (NOTE: It wasn't until after I did the repair that I heard 15 years is quite old for a washer. But it cost me $40 to repair compared to $500 to replace. I hope it lasts another 15 years!)

I am a maintenance mechanic and was very easy for me. I just loose i screw 10mm took out old parts put new parts in and it was ready to go again.

Gravy replacement! I pulled out softner dispenser,
undid the one bolt securing the agitator assembly, and removed the top half of the agitator. the cam assembly tapped out. I replaced the bolt so I could still use the machine while the parts were on the way. When the part arrived (36 hours later with 3-5 days expected) I removed the bolt again and followed the simple instructions to replace the cam. Saved a ton on repair costs!

First I came to this web site and discovered some directions from other customers. I then followed those directions to disassemble the agitator. I removed the softener cup by pulling up on the blue plastic retention ring. I then used a flat head screwdriver to remove the plastic cap by placing the screwdriver into the slot on the side and prying it off. Next I used a 3/8 socket and extension to remove the bolt which holds the agitator to the shaft. After the bolt was removed I pulled up on the agitator and removed it from the washing machine. To remove the upper section of the agitator, I placed it on the ground and holding the base with my feet, I pulled on the upper section. I then removed the dog ears, verifyed the problem and ordered the parts (dog ears). The parts arrived in less time than promised, were installed in about 5 minutes and I was back to doing laundry. When you reassemble the agitator, turn it upside down to install the dog ears so they do not fall out.