MVWC450WW0 Maytag Washer - Instructions

I pulled the hose off and notice their was a part # and I went online and type the part # and showed the part and cost. I order it and receive it within 3days. when the part arrive I replace the hose in minutes. If I can do so can you its that easy.

Pulled hoses off, unclipped the remaining retainer clip, slid old pump off. Slid new pump on replaced the old retainer clip and put the new one on, replaced the 2 hoses, done. It took mabey 10 min.
The part got there in less that 24 hours from the time I placed the order, with standard shipping! I was impressed.

Found leveling spring loose on bottom of washer, the sheet metal on bottom of cabinet ad rusted through. Drilled new hole in sheet metal and installed new leveling spring. Greased hole with blue marine grease so it will last another 40 years.

I removed the cap over the ratchet mechanism, removed the ut holding the agitator in place, removed the agitator and cleaned all the parts. The assembly for the ratchet dogs was a 3 piece assembly that was included in the kit I bought from Part Select. I also bought a new cap and gasket since my old gasket had broken too. A new gasket was already included in the kit, so I didn't need ot buy the cap. I liked that th ekit included everything I needed and good instructions. parts got to me in about 3 days. Very happy with my Parts Select experience and the fact I saved at least $100.

Followed the video. Removed the case and holder clips (not really needed) and replaced the springs. It did nothing to stop the problem and there are no more fixes.

Replaced the Washer Water Inlet Valve with Thermistor

I watched the repair video and found it to be very informative. The repair took me about 45 minutes but only because I cleaned the entire washer, inside and out while it was apart.

Removed the outside body of washer. Used 1/2 plywood between drum and wear pads to make space to pry out pads with screwdriver. Replaced suspension springs and tub spring (use waterproof grease on end of springs. Put washer back together and tested. Problem solved washer not walking all over floor anymore. Thanks for you help.

I popped of the fabric softner dispenser at the top auger by appling pressure with both thumbs rather than use the notch provided. This gives access to the agitator mounting bolt which was removed with a deep socket and extension on a ratchet handle. The agitator slipped right off the splined shaft by pulling upward at two points at the bottom. I ordered the complete agitator repair kit which included a part that improved the operation of the top auger, it may have been a factory upgrade at some point on this machine. I did use silicone grease where required and I feel that this is a must for longevity of the thrust washer. If you are ordering the complete kit, the o-ring seal for the inner cap is included. The machine washes like it was new.

I removed the cover for the softener dispenser on the top of the agitator. Then reached in and removed the cover of the nut and washer which was very sticky and sealed with an o-ring. This took a bit of pressure. Then used a socket wrench with an extension to loosen the bolt and took the whole agitator out of the machine. Then I set the agitator on the floor and with a fine 12 inch long screw driver released the catches while turning and pulling the agitatior with my other hand and holding the lower agitatior on the floor with my feet. I then turned the upper part over and removed the cogs and holding mechanism.
Then I reversed the process after replacing the cogs with the new part. 25 minutes total.

Took ten minutes to pop upper assembly off and replace dogs. Note long ratchet or nut diver advisable 5/8.

The old part popped right off, and new one installed. Works Great!!!

Followed your online video and it worked very well.

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

Disassembled top control console and surrounding sheet metal cabinet per the video from this site. i then used a screw driver to carefully pry up each wear pad location individually and inserted the wood wedge. to about 1 1/2 inch height. rwmoved the old wear pads and popped in the new pads one by one. Closed up the unit and tested the machine . It ran like new. No more noise or viberation