MVWC400VW0 Maytag Washer - Instructions

The tough part was replacing the front cabinet.
I did consult the video for help on replacing the clutch spring.
Thank you for that bit.

I admit to taking too much apart, most of the cabinet back can be left alone.
Some of the plastic wire keepers/routers suffered, as well as the console hinges.

The newly reassembled washer works without a hitch, and truely it took me about 4 hours over several days to dissamble and reassemble.
It is louder in the audible range than before, but very serviceale for another 20 years, saints willing.

Had no problem. The instructions included with the repair parts were very easy to follow and even specified the tools to use. I had it done, back on the washer and washing clothes in about a half an hour. The down side(no fault of the parts) was that the entire pump system went out on the second load and we wound up with a new Whirpool washer, since repairs were more than the machine was worth. Thanks Parts select for your help. I plan to search your net for more products. Fixing things from engines to microswitches is a hobby for me.

Unplug the washer. Used flat blade screwdriver under each end of the control housing on top of the machine. This popped the spring clips and allowed the control housing to be lifted up and rotated out of the way. Once out of the way, lift clip on wiring harness to lid switch, then pull the harness off. Use nutdriver to remove screw holding ground wire in place. Open lid of the machine. Pinch tab on back of the lid switch and rotate the switch up and out of the machine. Insert the new switch in the same manner, making sure that the machine lid remains open until the switch snaps into place. Attach ground wire using screw removed earlier and nutdriver. Clip wiring harness back in place. Close the lid and then rotate the control housing downward, and press on both ends to re-engage the spring clips which hold it down.

Pushed the new one into place. No tools, no fuss and very little swearing involved. Clogg was caused by erroneously pouring the liquid detergent into the very handy opening reserved for fabric softener. I'd love to say my wife did that, but.... no, it was me. NOW, the real story. I ordered the part via the web at 10:00 a.m. It was delivered to me at 9:30 a.m. the next morning via Fed Ex. Wow! Great job at PartSelect.

unplug washer. -remove two phillips head screws and two nut head screws holding control panel. -lift up control panel. -remove nut head screw on ground wire of switch. -release and remove switch. - put in new switch. - connect ground wire. -replace control panel and screws. -plug in washer. (depending on location of your washer move it to gain access to screws on back of control panel.- once done move washer back.)

researched the problem from the web-site.found the three most common things that would cause the problem.inspected the washer to see if there was evidence that one of the described parts had falled,and found that the tub wear pads were missing do to wear.simply replaced and it solved the problem. Thanks for the information.

Remove softener dispencer, use flat tip screw driver to remove agitator cap, there is a slot, insert flat tip screw driver and pry up, once removed you will see the damaged dogs or cogs, use 3/8 drive ratchet with 10 or 12 inch extention and if memory serves me correct a 9/16 socket, loosen bolt and remove top agitator, there is a thrust washer between bottom and top agitator, it comes in the kit, use a little grease preferrably water resistant grease on top of washer, replace top agitator then the plastic device that the cog are inserted into and tighten bolt, put agitator cover back on with a gentle slap of the palm and reinstall softener dispencer, you are done and cloths will agitate properly again, fairly easy job and washer agitator works like new, great kit, would reccomend.

I pulled the hose off and notice their was a part # and I went online and type the part # and showed the part and cost. I order it and receive it within 3days. when the part arrive I replace the hose in minutes. If I can do so can you its that easy.

took off the soap dispenser, removed the agitator using a 7/16" socket with an extension. replaced the old top agitator dogs and retaining ring with new ones, re-installed top agitator on bottom, thenput whole assembly back shaft, dropped in bold and tightened. whole experience was fast and simple. the parts came fast and where a perfect fit.

Removed power plug from the wall outlet. Removed fabric softener cup and inner cap seal to access the 7/16" bolt. I loosened the bolt and removed the whole agitator. I then placed the agitator on the floor and pulled the two pieces apart. I cleaned both agitator parts in the sink and installed the agitator repair kit using the instructions included and put the two halves back together. I then installed the agitator into the washer and tightened the 7/16" bolt, replaced the inner cap with new seal and inserted the fabric softener cup. I Then ran a load to test the repair.

Pulled hoses off, unclipped the remaining retainer clip, slid old pump off. Slid new pump on replaced the old retainer clip and put the new one on, replaced the 2 hoses, done. It took mabey 10 min.
The part got there in less that 24 hours from the time I placed the order, with standard shipping! I was impressed.

Followed the directions provided. Took less than 15 minutes and the washer works like new.

Very simple. Remove the fabric softener dispenser. Then remove the nut that is inside the agitator (requires a couple of extensions for your socket set). Remove the agitator by pulling up.

I replaced the 'dog ears' or agitator and the upper agitator. It is easy to see where everything needs to go after you take it apart. The upper agitator had plastic gears that were stripped and wouldn't have worked by only replacing the directional cogs.

Its easy, nothing to worry about.

Disassembled top control console and surrounding sheet metal cabinet per the video from this site. i then used a screw driver to carefully pry up each wear pad location individually and inserted the wood wedge. to about 1 1/2 inch height. rwmoved the old wear pads and popped in the new pads one by one. Closed up the unit and tested the machine . It ran like new. No more noise or viberation

As with any repair job, the hardest part is getting started and figuring out how to take it apart. I first tried to remove the top, by prying up on it,( his has worked in the past). This only broke the plastic retaining clips. I then removed the two plastic covers on each end of the control panel, then the two screws that hold the front of the control panel down. and lastly slid the control panel forward and out of its slots. I then used a 5/16th nutdriver to remove the four screws from the back panel. Now I was able to pull the panel back away from the washer body enough to use needle nose pliers to to remove the four electrical plugs located on the mixing valve. I used a felt tip marker to identify the locations of each plug. I used a 1/4 nut driver to remove the one mounting screw that held the valve in place and removed the valve. When the new valve arrived, It took about 15 minutes to re-install the valve and put everything back together.