3RMTW4905TW1 Maytag Washer - Instructions

The top portion of the agitator was not turning so that laundry could be drawn down in the wash tub. The problem was 4 little cogs that where worn and would not catch on a gear/cog portion of the bottom portion of the agitator. the cogs where about $10 delivered and it took about 25 min. to install (from top of washer). The old cogs, I also repaired by taking them out and using a hacksaw to redefine the grooves on them. They are still working, so I will hold on to the new parts until needed.

Removed the fabric cone from center of agitator pop out the plastic cover inside, remove bolt in center pull on agitator, remove cam holder and replace cams.
repeat process to re assemble

Pulled cap off top of agitator, loosened bolt down in center of assembly and pulled collar up with pliers.
Removed old dog ears and replaced. Need to be extra careful on direction of dog ears.

Very simple; even a cave man could do it!

I removed the fabric softner dispenser,removed the inner cover,removed the 1/2" bolt holding the upper agitator to the lower agitator and pulled the upper agitator up and out.Remover the cog holder from inside the upper agitator and replaced the old cogs with the new.They simply set loosely in the holder.I then reversed the process of putting the agitator back and bolting it in,inserted the small cover and dispenser.The entire job took about 5 minutes at most.

Took off softner dispenser, took off bolt cover. Used 7/16 socket with long extension and unscrewed bolt. Pulled up on agitator and out it came. Took out directional cogs and replaced with new. Reversed procedure and I was done. Saved a lot of money by not calling a mobile repair man on this one!

Removed fabric softener dispenser. Inserted screwdriver into slot on side of cover that is on agitator and pried off. Used socket extension to unscrew bolt inside agitator. Lifted out and slid off plastic ring holding agitator cogs . Replaced cogs in the same direction they came out. Since these instructions were here on site at the time I ordered the parts, it made the job very simple and fast...the order came very fast too.

First I removed the pop off cap at the top of the spiral shaped top agitator. Then reach down inside and pry off another pop off water tight cap exposing a 7/16 or 1/2 inch nut. A deep socket would probably be easiest but I didn't have one so a nut driver and luck got it unthreaded- it was pretty tight and yoiu have to hold the agitator from spinning while you unthread. Then the upper agitator asslembly lifts out and the cog assembly falls apart but it's only like 3 or four housing pieces and it only goes together one way to hold the four new cogs in place. reassemble and the machine works great again

I took out the fabric softener dispenser, then pulled of the plastic plate. There is 1 big bolt that has to be unscrewed in there. After that gets unscrewed, the whole agitator will pull out of the washer. I put the agitator on the ground, stepped gently with both feet on th bottom (mostly flat part). then I pulled on the top cylinder part, and the 2 parts separated. There is a little disk in the cylinder part that pops out. remove the top and replace the cogs. then put the disk back together. Push the two big main parts of the agitator back together...snap the disk back in and put the whole agaitator back in your washer. pop it back into place and screw in the bolt.....DONE! I have to replace these cogs about 1ce a year...it costs me about $5 and 15 minutes...but it keeps my waher running great!

Very easy repair. Popped off the top cap on the agitator with a flat head screwdriver. Then took a half inch drive socket set with the extender and removed the assembly where the cogs were housed. Inserted new cogs, put it all back together and the thing agitates like new. Simple. Saved huge dollars.

First take the top cover off, second using socket to turn the nut loose at the center, then removing the plastic holder which has four directional cogs in it, replacing them with new one.

disassembled two halves, cogs just sitting there, replaced, re-assembled

We took off softner cap and then took off the agitator with a nutdriver and then pulled the top off and the central agitator that the cogs were in pulled it out took the cogs out and replaced them with the new ones . Then we put the agitator back on and tightened the nut and replaced the softner cap and we were all done.

Took the cap off the agitator, loosened the nut with a wrench, and pulled the agitator out. The agitator pulled apart easily, revealing the piece containing the dog ears, which were clearly worn out. Simply replaced the dog ears and reinstalled the agitator. Piece of cake!

I just took the bolt out of the top of the agitator which allowed me to pull the agitator straight up. Then I turned it over so the sleeve that the cogs go into could fall out. I took the old cogs out, put the new cogs in, held it upside down and lowered the agitator down onto as to not move the cogs. When it was all situated correctly I held it by the bolt as I turned it upright. Then I just lowered it back down in place inside the drum and tightened the bolt back down. Done.
The washer works just like new.

Removed fabric softener dispenser. Inserted medium flathead screwdriver into slot on side of cover that is on agitator and pried off. Used socket wrench, socket and extension to unscrew bolt inside agitator. Lifted out and slid off plastic ring holding agitator cogs (cogs will fall right out so make sure you check to see how they're in). Replaced cogs in the same direction they came out. Very simple!!