MHWE201YW00 Maytag Washer - Instructions

I followed the video that accompanied the parts order confirmation. The replacement of the two parts, bellows and hose, were pretty straightforward. The job took a little less than an hour with little aggregation.

raised front of machine about 6 inchs bigest pain is getting water out after that its easy.open drain just a bit other wise it will pour out all over about 4 pots worth if its full

Pretty straight forward , It is a tight work are especially laying on your stomach. To make installation easier I recommend buying a 3-4 inch hose clamp instead of trying to use the old pinch style clamp. You will only need a zip tie if you reuse the existing clamps. remember to remove the plastic ball from the old rubber hose into the new hose.

After further investigation I realized that the original dispenser hose from the soap bin to the inner tip was the cause of the leak. Before this repair, I replaced the bellows. And as part of that replacement process you have to remove the washer dispenser hose from the inner tub so that I could complete the bellows installation. However when I put everything back together the old washer dispenser hose was leaking terribly. This was fixed easily with a new hose and an 1-1 3/4 inch hose clamp. I found an installation video that allows you to come from the top down to replace this hose but for my model of washer and because the drier was stacked on top, I took apart the front of the washer since I learned from a different video how to do this in order to install the bellows. No more leaking at all with the new hose.

This repair is something even the most casual DIY'er could accomplish. What made this even easier for me was the fact that my washer was on a pedestal so accessing the 1/4" screws were extremely easy. There is no need to tilt or lift the washer. Just open the drawer and all three screws are visible. It also made draining the water out of the washer very convenient. The video perfectly describes how to accomplish the repair and allowed me to diagnose the problem by taking off the panel, opening the trap door and allowing the water to drain into a small trashcan until all the water is removed. I could physically see that the impeller was detached from the motor and found the culprit that caused the problem - a small vile of eye drops... From there, ordered the pump, two days later, replaced it with the new and I swear the new pump must be stronger than the original because towels come out near dry after a spin cycle. Very satisfying repair!

Checked for 120 V AC at pump connector. It was present . Pump was hot. Ordered new pump. Changing the pump is a piece of cake. Just tilt machine back and rest on a brick. Remove 3 5/16th screws . Disconnect 2 hoses and 1 plug. Took 10 minutes tops. Back in business.

Ordered a new one. It was here on the second day. Lined it up, gave it a slight hit to snap it in place and I was ready to go. Didn't even miss a laundry day. I'm 70 years old and I had no problem doing the repair.

Boyfriend followed directions and YouTube and I’m sooooo grateful!! My door shuts easily.. I love my machine and my man with your directives and your parts made my magic happen!!

Only needed a pair of pliers for the clamps on the hoses connected to the pump. Removed the old pump ( no tools needed) and reinstalled the hoses. Works like a charm!

This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks

took the old part out by the front panel and put the new pump in and now it works great. only took a couple of minute to put the new one in. thank you for saving my washer.

Took less than 5 minutes to replace, So Happy;-)

The only issue I had was getting the hose from the tub re-installed, but that was my fault, the pump went right in. It couldn't have been easier. I was very pleased, received the replacement pump in just a couple of days, packaged very well for shipping, and had it installed in a matter of minutes. It took longer to take off front panel to access pump than it did to install it. Very pleased with "Part Select".....will use again!

Thank You so much for the other stories folks wrote on here! We were getting an F21 code on a regular basis. After finding a necklace and about $2.50 in change in the filter tray we found the problem. Over time I thought the washer was getting louder but it was so gradule that we really did not realize it.I had read other posts on here and ordered a new pump. After taking out 3 screws and 2 clamps the pump came right out and went in just as easy. Less than 15 minutes and we were back in business with a wisper quiet washing machine,Thanks Again everyone, Mike D.

I drained the water out of the pump area. Then took off all clamps and holding brackets. Next I pulled off the quick connect power plug. Then I put new pump in the way I took old pump out. The hardest part was unscrewing the bracket from underneath the washer. Cloth washer working fine.