MHWE251YL00 Maytag Washer - Instructions

turned off water to mach. removed the top off the mach. with scket, removed old valve and replaced it with the new one, very easy.

It was real easy. I disconnected the wiring as shown in the video. I took the clamps off the drain pump , once off I slid the old drain pump off. I slid the new pump on , attached the hoses with the clamp provided and connected the wiring. Just follow the video and you will find it to be very easy! Thanks Parts Select for saving me money

Replace water pump

Took of the panel, unscrewed the old drain, screwed the new drain in. Very very simple to do! The first part I received leaked, I called customer service and they gave me a refund and express shipped a new part - no questions asked. Very good customer service!

Thank You so much for the other stories folks wrote on here! We were getting an F21 code on a regular basis. After finding a necklace and about $2.50 in change in the filter tray we found the problem. Over time I thought the washer was getting louder but it was so gradule that we really did not realize it.I had read other posts on here and ordered a new pump. After taking out 3 screws and 2 clamps the pump came right out and went in just as easy. Less than 15 minutes and we were back in business with a wisper quiet washing machine,Thanks Again everyone, Mike D.

I drained the water out of the pump area. Then took off all clamps and holding brackets. Next I pulled off the quick connect power plug. Then I put new pump in the way I took old pump out. The hardest part was unscrewing the bracket from underneath the washer. Cloth washer working fine.

Took less than 5 minutes to replace, So Happy;-)

dryer stacked on top of washer. had to lift washer and block w/2 x 4 to get under unit and replace pump

Searched internet for diagnosis. Ran diagnostic test using the diagnostic manual from whirlpool. The error code was F29. Replaced door latch but problem was not solved. Then order the Motor Control Unit. Removed old control unit through the top by removing the top washer cover and numbering harness positions with painter's tape. Install the new Control Unit and ran diagnostic procedure. The problem was solved. The washer is working fine.

Well first off the part is different then the orignal so it does not fit correctly. I removed the old bellow and its cicular spring clamps. On the new bellow there is not enough lip on the rubber for hte clamps to be put back on and hold the bellow in place so it still leaks out the door. if the part was a match it would work but since the part number was changed and the design was changed it now does not fit correctly. INstructions did not come withthe part so had to find them online.

Turn off water and power. Pull top off first, then bottom front kick plate. Take all the screws out of the soap tray. Disconnect the front panel from the controller, then the upper front panel comes off, but be careful with it as it is plastic tabbed. Pull upper metal support brace off. Detach the door lock BEFORE you pull the door off (two torx screws). Take a flat head screwdriver and release the spring holding the bellows to the front door/panel, then fold bellows into washer a bit. Remove front door/panel. Back bellows clamp is Phillips, loosen and remove bellows. reverse steps to put back together, but run machine in rinse/spin with top and front lower kick panel off to make sure of no leaks. Also good time to check pump lint screen for junk in it too.

This part worked great! Completely fixed all the problems that I had with my washer. A bit hard to actually place it in(pliers are necessary) but otherwise very easy to install.

Unplugged washer first! Removed front bottom panel by removing three screws, unscrewed the Drain Plug assembly by turning drain plug counter clockwise with a bucket to catch excess water from washer. Used pliers to remove spring clamps from washer agitator drain hose and then removed the spring clamp from the hose going to drain. Checked hoses for obstructions, then Slide Drain Pump assembly up to the right to remove. Then installed new Drain Pump assembly by sliding pump into slot to the left. Connected the agitator and drain hose to new Drain Pump and fastened with spring clamps. Plugged in AC line cord and turned washer on and started a quick wash cycle to check for leaks and to see if the water drained from washer properly. The water drained from washer and error code did not appear. The error code F21 reappeared during the second wash cycle. After closer inspection with a flash light, I found a large piece of cloth caught between the washer agitator and washer tub covering the drain by shining the flash light up towards the Agitator tub. This was solved by removing the Drain Pump assembly and all of the drain hoses again. Then removing the the large hose from the agitator tub and then removing the large piece of cloth from agitator tub. After reassembly, the washer worked like new!

The key to this repair is 1) lifting the front of the washer to access the bottom trim bolts, and 2) using lubricating spray around the outer bellows clamp area and 2 people to work the clamp into place.

removed top,3 screws in back,lift up and pull back.removed soap dispenser.removed hidden torx screw on left side. removed screw top center of door opening,used putty knife to pop control panel off and laid on top of washer.used small screw driver to pop off front gasket spring and wire from left side.took gasket loose and remove door lock and let it hang there,took off kick panel and front then un screwed the inner gasket retainer,pulled off gasket.soaped up new gasket and reinsalled in reverse order..it took two of us to get the front spring and wire back on,that spring is tough and the gasket kept popping off,finaly got it,works fine