MHWE450WW00 Maytag Washer - Instructions

Remove old belt, rotate large washer belt wheel, guiding belt off large wheel.
Guide new belt onto Washer Large Wheel. Use a pair of pliers to hold belt onto wheel as one turns the large washer belt wheel, guiding belt onto wheel. Note belt will be tight. Seems like belt will not fix but keep going it will fit, you might even hear it pop on.
Old Part number (W10116215) new replacement Part number (W10388418).
New replacement washer belt fits tight, that is ok.

remove door from washer and lay flat on a piece of cardboard remove 4 screws from door hinge and take out just enough screws both sides of hinge to remove hinge from pocket of door,careful not to put to much stress on glass and gasket when removing old hinge and replacing.

very simple

Replaced pump

I removed the back panel to access the top end of the hose then I removed the lower front panel to access the lower end of the hose that attaches to the pump. The hose is secured with spring clamps and they were removed with pliers, the panels are secured with screws.

I replaced the hose and reinstalled the panels and I was done.

We read your you tube instruction and followed the video

Remove top and front
Care taken to unplug door wiring
should have taken notes or photos where srews go and order
remove old bellows large hose clamp and sping tensioned clip
clean surfaces
install new bellows on tub only
put all panels and door together
Connecting wiring to door and strain relief takes 2 people
connect bellows to door with spring clip

Unscrewed two screws to remove old faceplate backer. Screwed new faceplate backer to detergent dispenser. Snapped new face plate on to the backer. 5-10 minutes tops.

The plastic tabs were too large to fit into the washer's slotted hole in the washer cage. I initially bought this part from a PartSelect competitor and it was made wrong as well. Whirlpool themselves showed this part on back order so the faulty part originated in a Whirlpool order to a vendor. The reason for this reply is that PartSelect resolved this bad part issue within 2 hours and 1 phone call. The competitor has not resolved anything yet in 3 weeks and 5 emails with image proof.

Followed internet instructions

The end of the strike had broken off, and the pictures did not clearly show there was a cross-member at the end of the strike. That crossmember is what broke on the old strike. The strike has only two screws, both requiring a Torx bit (#20, I believe). Unscrew both screws to remove the strike plate. It was a little difficult to get out - it has a curved top to lock into the top slot, but the bottom slides slightly down into another slot. There isn't a lot of room in the opening to slide the strike up and down and get it out. Putting the new strike on is easier - ensure the curved end fits into the slot at the top and slide it up just a bit, push the bottom of the strike plate in, then let it drop right into place, and reinsert the screws. The only problem I had was the strike's holes for the screws are slotted horizontally, so the strike can be positioned across almost 3/8". The latch would not engage the strike the first time, so I had to loosen the screws and reposition the strike a bit. This time it latched, but the fit wasn't quite right, so I adjusted it again to get it where I needed it.

firts remover the three bolts that held the front panel on, and removed that. Then removed the screw that held the pump in place. then removed the hoses from the pump. After that put hoses on new pump and srewed back in place . the put front back on.

We removed the front cover to the washer. Then we removed the drain pump piece that was broken. We put the new drain pump in and secured the screws. We also inspected all the hoses to make sure the hose clamps were intact. Then leaving the front cover off the machine to inspect for leaks we turned on the wash cycle. No more problems.

Myself...easy

Lineup slots and snap in place. So easy even a caveman can do it.

Easily. 4 Screws. 2 Clamps.