MHWE450WW02 Maytag Washer - Instructions

First I want to acknowledge Parts Select for their prompt delivery(received parts in less than two days)and their unbeatable prices(approximately 1/3 less than two local appliance repair/parts shops). Repair was straight forward a simple swap of the pump and I saved quite a few dollars.Thanks Parts Select.Any future appliance parts needs will be purchased here.

Very limited access to the bellow clamp. Found it easier to first remove washer front panels (8 screws total), providing ready access to R&R the bellow. 40 minutes tops.

I removed the top 3 screws on the rear, removed soap dispenser, removed screw in front corner at soap dispenser,pry off control panel with flat head screwdriver lay on top, removed spring around bellows at door opening, remove 4screws holding door assembly, disconnect 3 molded plugs serving door lock, you will need to hold door while you loosen bellows clamp.Reverse process note: soap dispenser tube can be removed to clean without any tools. It is some much easier when you remove the front door assembly.T-20 torx screwdriver, 9/32 socket Theirs a you tube video also.ghw

Very easy. Revived back of washer. Used a screwdriver to pull belt over pulley. Very easy

Washed three loads and it was ok but then it stopped draining again. I don't know what to do.

Looked at how the old drain pump was installed, then removed it and installed the new one. It was a fairly simple fix. The only feedback were that the parts picture was a little confusing becuase the picture didnt really look like the actual part, so we were unsure if we were ordering the correct part.

Unplug washer. Open door. Look at the very bottom of the bellow and will see a spring that is connected to a small wire that runs around the bellow holding the outside on. Using a flat head screw driver insert it between the wire and bellow, pull down slighty. Grab the wire and gentley pull off. Now the outer part of the bellow will be free, pull it toward you, and off the water/soap despinser, then push it into the washer. Now look to the right side and you will see a screw head that is actully a big clamp ring around the bellow. This is the hardest part. Use a small rachet screw driver with a 7mm socket to lossen. Pull clamp off gently, you can now removwe the bellow. Put bellow back on in reverse. There will be a small tab on the bellow it goes to the top. Took about 2 hours.

Followed video, slowly. Was easier then I expected. Everything fit perfectly.

We hired a local repairman and he even had trouble . I would not suggest anyone trying this installation on their own. It took the repair guy an hour to do and he struggled. Not an eary installation

First unplug the washer and take the back cover off. Loosen the screw on the motor and the big nut on the belt wheel. Take the old belt off and put the new belt on around the motor but slip the motor back in place with the screw slightly in place but do not tighten it yet. Place the belt around the motor and the wheel but this is hard because you need some one with some strength so the is where my dear boyfriend came in handy. He used his strength to stretch the belt and put it back on the machine so I could put the big nut back on. But if you break a wire you have to know a little electrical to put back the wires back in place with small connectors. I do know electrical also. My machine is working better like new. Carol Rozier

Opened lower front panel to access the motor controller. Took a picture of the wiring attached to the front of the controller. Removed two wiring harnesses and one wire with a retainer clip. Removed the faulty controller. Inserted the new controller, replaced the wiring, using the picture to insure correct positioning (although that really wasn't necessary because the wiring clips could probably only be put in the correct places). Replaced the front cover, plugged in the washer and fired it up.

Followed video clip that I found online

open the front bottom panel (3) screws. remove panel. twist off old shocks by turning the shock counter clockwise. reinstall shock by turning clockwise.

Made a bad call after googling "bearing squeal for HE 4t" and replaced the bearings and seal on the drum.... Turns out my squeal was coming from the drain pump, didn't realize until after a major tear down and replacement of bearings and seal. Managed to break one of the electrical connectors on the heating element on that repair as well... Compared to the bearing replacement the drain pump was super simple. Lots of good instructions above, the only thing I would add is that if you put a little pressure on the hose clamps and spin them to an easier position to see and get pliers on, they will be much less of a headache. Vice grips were the best tool for getting them released and re-installed. The heating element was pretty easy, loosen the center nut to the end of the threads but don't remove. Use a flat screwdrive to gently pry the unit out. Use a little dish washing soap to lube up the rubber plug on the new one before installing and it slides right in.

It was a little difficult to put the new Bellow in place on the tub, due to the fact you have to basically push the outside of the Bellow all the way into the tub so you can install the tub clamp. The other difficult part of the task was tightening up the clamp it's self. There really isn't a lot of room to move your hand around in the space you are given to work. But after a few hand cramps and a few things said, that are not needing repeated, I was able to get the clamp tight. Once you have the clamp on the tub, it's basically pretty simple to slide everything else into place. The wire/spring clamp that is used to attach the Bellow to the front of the washer is fairly simple to put into place with a little patience. All in all it was a cheep and easy repair for a due-it-your self repair.