MHWE500VP01 Maytag Washer - Instructions

Unplugged electric cord and turned off water supply. Remove 3 screws @ rear of washer and removed top panel. Removed clamps on hoses and electrical connector to flow meter, removed and replaced with new flow meter. Replaced the top panel, turned on water supply and plugged unit in. Finished in less than 15 minutes. Saved myself several hundred $

Took of the panel, unscrewed the old drain, screwed the new drain in. Very very simple to do! The first part I received leaked, I called customer service and they gave me a refund and express shipped a new part - no questions asked. Very good customer service!

I opened the top by taking four screws from the back and lifted the top. The part to be replaced was clearly in view. I opened the clamps on the hoses, pulled the hoses off, removed the wires, and reversed the process with the new part. The washer works great now! I ordered the part on a Friday, and it was delivered the next day, even though I didn't pay for overnight!

unplug washer from outlet carefully tilt back to get at underside of washer remove bottom panel. pump location lower right front. remove two hoses from back using pliers keep note on hose location. remove two bolts on underside of machine slide pump to the right to release from rubber holders to install reverse the process also good idea to use the new hose clamps that come with your new pump and the rubber mounts if they are included

Very easy. Revived back of washer. Used a screwdriver to pull belt over pulley. Very easy

Removed top of washer and replaced flow meter.

I watched video first and it help me a lot to do the repair myself of my washer machine and i save about $ 1,500 dollar. Thanks

Read the instructions provided by PartSelect.....and with a bit of patience I installed all four bolts so the washer's inside agitator was not damaged in shipping. I highly recommend that anyone who is moving/storing or shipping their washer that you find the correct shipping bolts according to your model and make and install them prior to moving your appliance.

Put towel down to catch excess water, opened drain screen, used pliers to remove squeeze clamps on both hoses, removed front hold-down torx-head bolt and slid pump assembly out. Compared new part to old and found 2 differences 1:no hold-down location in front for bolt,2: the rubber padded feet are not the same. I was able to remove the two screws on the right side and use just the rubber pad for support while sliding the left side in the slot and is was plenty stable and works just fine. I guess the Whirlpool Duet model is a bit different on mounting but everything else fit quite well, the washer is working perfectly again.

repair was a cake-walk with the video there to help.Thanx

Followed instructions from a You Tube video. I'd recently lost my job and money is tight and I thought we could save money doing it myself. By watching the video and ordering parts from you we were able to save $500 between parts and labor. Thanks

First unplug the washer. Make sure and drain washer completely. If not drained remove front panel , Remove 2.5 inch Plastic drain cover which has a catch bin on it. This will allow it to drain the washer. Put pan underneath to catch the water. Tip washer back and prop up with something 6 inches tall to get to the screws underneath. A cement block would work well. Use pliers to squeeze hose clamp together to remove the Hoses. Gently lift up The flip down cover Over the top of the wire harness Push in the tab on the wire harness, Gently pull back on the wire harness. Remove two mountings screws from the bottom of the washer. Slide the whole pump housing to the right and Lift up. Now the pump is been removed. Inspect inside the hoses For Debrie. Remove anything that is left in the hoses. Reinstall the pump in reverse order from the way you took it off. Leave front panel off Make sure all hoses and wire harness are hooked up. Run wash cycle to make sure there are no leaks. Do not put hands in while running. If no leaks replace front panel. Not sure if this is the right way But this is the way we did it and it worked well. Washer runs quieter now than it did when we got it

Watched a YouTube video, saw how simple it was. Did all the things the video said to do. Then it said that if the error code came back, by the part. I bought the part SUNDAY night and it was under my door mat Tuesday when I came home from work. Removed three screws, took off the top of the washer, plugged the electronics, shoved the little hose on, put the top back on and boom, no problems! Now, if I could just find a YouTube on a Fisher Paykel dishwasher, I'd be in business... Great part, reasonable price, great service, great shipping.

open the front bottom panel (3) screws. remove panel. twist off old shocks by turning the shock counter clockwise. reinstall shock by turning clockwise.

Very --simple remove front acess panel -- open sump clean out remove water out of existing pump an hoses with small wet dry vac -- remove small wire harnes --cut band clamp on discharge with side cutter --remove inlet -suction side of pump hose clamp with channel locks --un bolt two screws on bottom side of washer with 5/16 nut runner --discard old pump reinstall new one in reverse order --only takes about 20 mins total !!! ---