MHWE500VW00 Maytag Washer - Instructions

Simply removed 3 screws from the back of the washer, twisted the part to the side to remove it from the slot it fit in. Removed the hose, them removed the wiring plug. Plugged in the wiring to the new switch, put the hose back, slid the switch in to the proper slot, twisted it into place, replaced screws and cut the washer on! BINGO!! Been working like a dream.

I followed the repair blog by the poster most liked...

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

The water pump housing was leaking due to some pre-existing damage and leaking on the floor. The repairman wanted 60.00 just to show up. I purchased a replacement pump from PartsSelect.com and installed it myself by taking off the bottom front panel (two screws on the bottom and unclamping the two hoses from the pump and the two screws holding the pump to the frame and then unsnapping the wiring coupler from the old pump. I pulled the old pump out through the front of the machine. I then installed the new pump and replaced the front cover. I saved myself a lot of money and everything went smoothly! The machine works great.

Open the bottom screws (hex-screw driver. remove riongs with pliers. use pan to remove excess water remained in pipes. pull to the right and remove. easier than it seems,

remove 3 screws of top panel at rear. slide top to rear 1/2 inch and lift up. disconnect wire to flometer, remove clamps on hoses and remove, reverse to install. did not fix problem. ck'd screens at fill valves. ordered new fill valves--problem solved. solenoids must not have been opening up all the way.

Serviceman had previously replaced the hot and cold inlet valves, but the low pressure error persisted. Rather than cough up another $130 for the serviceman to return, plus parts and time, I decided to order the replacement flowmeter from PartSelect.

Unplug power and turn off water. Top of machine comes off by removing three screws at top rear; use socket, spanner or T20 driver. Unplug electric sensor from flowmeter. Old unit is removed, and new one connected to water line by squeezing spring-clips with a pair of flat nose pliers. Reconnect electric sensor.

Great move, easy, and saved myself the thick end of $200.

I romoved the front of the washer access panel. I then used the pliers to remove the clamps from the old hose and to replaceit with the new one.

After replacing the Water Inlet Valve and Flowmeter the F20 error message stopped. However, after ordering and replacing the Water Pressure Sensor the F35 error message and the SUDS error message stopped and the washer is finally working.

First step was to remove old bellow. I opened the door there is a small wire with a spring attach that holds the outside of the bellow to thw washer. Then removed it from the water inlet, then took a short straight scewdriver to remove the gaint hose clamp holding it to the drum. Installed the new part. When putting hose clamp back on I removed the top of the washer by removing the three screws in the back then I flipped the hose clamp so I could use a long screwdiver from the top side.This will give you alot more room. Hope this helps

Removed bottom panel, removed hoses and pump. Reinstalled in reverse order.

Overall, the install was easy.
Just a matter of getting yourself to get it done.
The video on the removal / install procedures was most helpful.
The front shocks were completed very quickly. The rear shock required all hoses to be disconnected and the back of the washer to be removed. After removing perhaps a dozen screws the cover was still fastened. You will see (in my case) 4 plastic flat clips. after they were removed the back came off. The rest of the project was the same as the front shocks. 1st time thru so to be expected.
Anyway, certainly a project that any DIYer can tackle.
Thanks Partselect for the correct parts in a timely fashion and the knowledge to perform the install.
Scott

Removed washer door from washer. Lay door on work bench (table). You need to remove screws from around most of the washer door to remove broken hinge. Install hinge into door frame. Fasten all screws for hinge and door frame. Reinstall complete door assembly onto washer with removed screws. Helpful to have some hold door for ease of alignment. Tools used: 1/4 inch torque #15 bit with 1/4inch nut driver.

Brother who used to sell appliances opened the washer door and read the booklet inside the washer telling him the part necessary to repair the problem. $33/00 for the water flow meter Part and shipped in next morning and arrived overnight. Excellent service for only $7.00 shipping. Highly recommend this place for parts. This was after a couple of days searching the internet for those with the same problem and not receiving and exact part to fix the problem

Tried all the Internet fixes and nothing worked. Bough the part put it in and BINGO! problem fixed. This is a class-action suit waiting to happen -- will never buy Whirlpool again. The stink problem persists despite cleaning and more cleaning.