MHW7000AW2 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Wichita Falls, TX
- Parts Used:
- W10575334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Dispenser inlet connection broken
1 Pull the machine away from the wall.
2 Unplug the machine.
3 Remove three screws in the back on the machine that secure the top
4 Remove the top
5 Remove the water lines that are connected to dispenser
6 Remove the Detergent tray
7 Remove one 1/4-inch screw that secures dispenser to the washer brace
8 Remove two torques tip screws from the front of the dispenser
9 Remove the outer ring securing the washer seal
10 Disconnect the rub hose connected at the front of the dispenser at the bottom
11 Reinstall the New Dispenser in reverse order
12 Test for leaks
2 Unplug the machine.
3 Remove three screws in the back on the machine that secure the top
4 Remove the top
5 Remove the water lines that are connected to dispenser
6 Remove the Detergent tray
7 Remove one 1/4-inch screw that secures dispenser to the washer brace
8 Remove two torques tip screws from the front of the dispenser
9 Remove the outer ring securing the washer seal
10 Disconnect the rub hose connected at the front of the dispenser at the bottom
11 Reinstall the New Dispenser in reverse order
12 Test for leaks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from WADING RIVER, NY
- Parts Used:
- WPW10365885
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Shipping delay FedEx four days in Chicago was curious.
Old dispenser part came loose from dispenser drawer area, hit the floor and broke two plastic connectors. Very small and fragile plastic tabs are all that retains the front of the dispenser drawer. Cost for those two parts over $100 retail.
Be gentle with plastic components.
Be gentle with plastic components.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WILLINGTON, CT
- Parts Used:
- WPW10605427
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Socket set
E1 F9 code. Cannot drain.
Removed back panel. Remove 4 8mm sockets on pump assembly. Replace with new pump. Only difficult because of limited clearance. But I'm huge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HARRY from OZONE PARK, NY
- Parts Used:
- WPW10208415
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken hinge on door
Took door off with a Phillips screwdriver went to hardware store with door so he could match up the 6pt screwdrivers that were needed.
No more then 1 hour to do.
No more then 1 hour to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from LAKE STEVENS, WA
- Parts Used:
- WPW10605427
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Error Code F01 E09 (Drain Issues)
Unplug appliance. Remove the back panel with the 1/4” nut driver and cordless drill. The pump is located as you face the back of the machine on the bottom. Remove four screws that hold pump in. Reverse the process and install new pump. Check the filter and clean out the housing.
Reinstall back panel and plug back in. Run a test load (no clothes) and test drain.
Reinstall back panel and plug back in. Run a test load (no clothes) and test drain.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Salt Lick, KY
- Parts Used:
- WPW10467289
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer posting a f6 error
This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David D from Severn, MD
- Parts Used:
- WPW10488048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Strike on Washer Door - prevented door from latching, and washer would not start
The end of the strike had broken off, and the pictures did not clearly show there was a cross-member at the end of the strike. That crossmember is what broke on the old strike. The strike has only two screws, both requiring a Torx bit (#20, I believe). Unscrew both screws to remove the strike plate. It was a little difficult to get out - it has a curved top to lock into the top slot, but the bottom slides slightly down into another slot. There isn't a lot of room in the opening to slide the strike up and down and get it out. Putting the new strike on is easier - ensure the curved end fits into the slot at the top and slide it up just a bit, push the bottom of the strike plate in, then let it drop right into place, and reinsert the screws. The only problem I had was the strike's holes for the screws are slotted horizontally, so the strike can be positioned across almost 3/8". The latch would not engage the strike the first time, so I had to loosen the screws and reposition the strike a bit. This time it latched, but the fit wasn't quite right, so I adjusted it again to get it where I needed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Ardmore, AL
- Parts Used:
- W10763470
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Had to install shipping bolts so we could move the washer
Really was not a repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from Middletown, NY
- Parts Used:
- W10869845
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Washer Would Drain But Not Spin
Removed rear cover (6 screws) unpluged harness from motor control and removed same. Replaced motor control reinstalled harness. Replaced rear cover. Parts used motor control board.
Was this instruction helpful to you?
Thank you for voting!