MHN33PDCXW1 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- kevin from elizabethton, TN
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Washer washed cloths then would not rinse
Just went by instructions provided by parts web site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LINDA from CHESTERFIELD, SC
- Parts Used:
- WPW10212596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
intake valve was leaking
turned off water to mach. removed the top off the mach. with scket, removed old valve and replaced it with the new one, very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Naples, FL
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
My washer was not draining
It was real easy. I disconnected the wiring as shown in the video. I took the clamps off the drain pump , once off I slid the old drain pump off. I slid the new pump on , attached the hoses with the clamp provided and connected the wiring. Just follow the video and you will find it to be very easy! Thanks Parts Select for saving me money
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from SAINT CHARLES, IL
- Parts Used:
- W10822553
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
washer jumping when spinning
open the front bottom panel (3) screws. remove panel. twist off old shocks by turning the shock counter clockwise. reinstall shock by turning clockwise.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Waco, TX
- Parts Used:
- WPW10730972
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Wouldn' drain f21 then after I drained it it gave f33
Replaced the pump assembly. The different type of clamp supplied in the kit was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Ruther Glen, VA
- Parts Used:
- WPW10730972
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Drain pump was not working properly
First, I watched the video again just to make sure I had a firm grasp of the task ahead. I gathered up the tools and proceeded to begin. First obstacle: getting the washer tilted back enough to put the blocks under the front feet. The washer was sitting inside a square water pan with a drain connected directly under the middle of the washer. Therefore, the water pan did not move and I could only get the washer moved out far enough to 'barely' put the blocks underneath. Second obstacle: a clump of hair had gathered at the bottom portion of the door unnoticed and caused a slow leak from the bellows. This leak dripped down and rusted out two of the three screws. I had to use a socket set to get the screws out. Third obstacle: getting the pump removed from the bottom of the washer. With the drip, the pump had stuck to the bottom of the washer. Trying hard not to get cut on the sheet metal bottom, I pushed and pushed and pulled until finally the pump let loose. From that point on..smooth sailing just like the video. Washer fixed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Dayton, TX
- Parts Used:
- WPW10730972
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Making noise, not draining properly.
Put towel down to catch excess water, opened drain screen, used pliers to remove squeeze clamps on both hoses, removed front hold-down torx-head bolt and slid pump assembly out. Compared new part to old and found 2 differences 1:no hold-down location in front for bolt,2: the rubber padded feet are not the same. I was able to remove the two screws on the right side and use just the rubber pad for support while sliding the left side in the slot and is was plenty stable and works just fine. I guess the Whirlpool Duet model is a bit different on mounting but everything else fit quite well, the washer is working perfectly again.
Was this instruction helpful to you?
Thank you for voting!