MHP30PRBWW0 Maytag Washer - Instructions

First thing, unpluged the washer. I removed the lower front acces panal. I then propped the washer up on 2 pint sized paint cans to reach the pump mounting screws. I disconnected the wire bundle going to the pump. Then removed the inlet and outlet hoses from the pump. Then I removed the 2 mounting screws on bottom and slide the pump to the left and removed. I then pump the new pump on the same way I took the old one off, but in reverse. Easy and fast the worst part was the price of the pump.

I was already very familiar with the motor & drain pump, as I had disassembled my original one in attempt to find the problem & fix it. Finally, I broke down & purchased a new one. It was VERY easy to install! The most difficulty was finding the right sized board to put underneath & raise the machine up (with the dryer attached to the top of it) to place the board underneath so that I could tighten the bolts from underneath to attach the pump. After that was over, the rest was cake! Just attach the hoses & the electrical, which just clips in place & my washer is like new again! Yay! Oh, and yes, I'm a woman DIY'er.

We purchased a new pump and installed it very easily. My washer works great!

Followed instructions from a You Tube video. I'd recently lost my job and money is tight and I thought we could save money doing it myself. By watching the video and ordering parts from you we were able to save $500 between parts and labor. Thanks

First unplug the washer. Make sure and drain washer completely. If not drained remove front panel , Remove 2.5 inch Plastic drain cover which has a catch bin on it. This will allow it to drain the washer. Put pan underneath to catch the water. Tip washer back and prop up with something 6 inches tall to get to the screws underneath. A cement block would work well. Use pliers to squeeze hose clamp together to remove the Hoses. Gently lift up The flip down cover Over the top of the wire harness Push in the tab on the wire harness, Gently pull back on the wire harness. Remove two mountings screws from the bottom of the washer. Slide the whole pump housing to the right and Lift up. Now the pump is been removed. Inspect inside the hoses For Debrie. Remove anything that is left in the hoses. Reinstall the pump in reverse order from the way you took it off. Leave front panel off Make sure all hoses and wire harness are hooked up. Run wash cycle to make sure there are no leaks. Do not put hands in while running. If no leaks replace front panel. Not sure if this is the right way But this is the way we did it and it worked well. Washer runs quieter now than it did when we got it

dryer stacked on top of washer. had to lift washer and block w/2 x 4 to get under unit and replace pump

Perfect part...saved me hundreds on labor. Thanks!

Unplugged washer first! Removed front bottom panel by removing three screws, unscrewed the Drain Plug assembly by turning drain plug counter clockwise with a bucket to catch excess water from washer. Used pliers to remove spring clamps from washer agitator drain hose and then removed the spring clamp from the hose going to drain. Checked hoses for obstructions, then Slide Drain Pump assembly up to the right to remove. Then installed new Drain Pump assembly by sliding pump into slot to the left. Connected the agitator and drain hose to new Drain Pump and fastened with spring clamps. Plugged in AC line cord and turned washer on and started a quick wash cycle to check for leaks and to see if the water drained from washer properly. The water drained from washer and error code did not appear. The error code F21 reappeared during the second wash cycle. After closer inspection with a flash light, I found a large piece of cloth caught between the washer agitator and washer tub covering the drain by shining the flash light up towards the Agitator tub. This was solved by removing the Drain Pump assembly and all of the drain hoses again. Then removing the the large hose from the agitator tub and then removing the large piece of cloth from agitator tub. After reassembly, the washer worked like new!