MVWC415EW1 Maytag Washer - Instructions

Removed belt cover from bottom of the transmission , remove old belt, clean the pulleys ,and re install new belt. The new belt fits tighter so it did a few time to get the belt fully seated. Re install belt cover.

Nothing to it. Just remember to put the insert in the knob, NOT on the selector stem. Line up the flat part of the insert with the flat part of the stem and push the knob in place.

Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicates the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.

THE NEW LATCH COMES WITH A NEW BEZEL ATTACHED, WHICH MOUNTS TO THE TOP OF THE WASHER, JUST UNDERNEATH THE LID. BECAUSE THE ORIGINAL BEZEL WAS IN PERFECT CONDITION AND DIFFICULT TO REMOVE, I DECIDED TO REMOVE THE BEZEL ON THE NEW LATCH, AND USE THE ORIGINAL ONE. THIS WOULD HAVE TO BE DONE REGARDLESS IN ORDER TO INSTALL THE NEW LATCH. REMOVING THE BEZEL WAS DIFFICULT DUE TO ALL THE LOCKING TABS THAT KEEP IT IN PLACE. I HAD TO RESTRAIN THE SLIDING SWITCH PARTS WHILE I REMOVED TO BEZEL TO AVOID THE ASSEMBLY FROM COMING APART. ONCE I SNAPPED THE NEW LATCH TO THE EXISTING BEZEL, THE ASSEMBLY WORKED FINE. TAKE TIME TO STUDY HOW THE LATCH ASSEMBLY IS ATTACHED TO THE BEZEL SO THAT YOU DON'T BREAK SOMETHING. USE A VERY SMALL SCREWDRIVER TO PRY BACK THE PLASTIC TABS IN ORDER TO RELEASE THE BEZEL FROM THE LATCH ASSEMBLY.

slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys

Force the thin nylon strap around and down into the perimeter of the agitator. Draw it snug to the center. The strap must be long enough to make a complete loop up to the top of the tub. Insert a fairly stout wooden stick through the loop so that an upward prying motion of the stick applies a vertical force on the agitator. While the force is applied pound on the lower part of the agitator so that it will break it free from the motor's axel. Of course remove the center bolt first after removing the small hub cover.
Applying liquids to the connection did not help. Just a steady upward force and a few rubber hammer blows to the lower part of the agitator di the trick.

I had taken the time to watch videos of this repair so when the switch arrived I knew what I had to do. Removing the screws to get the back cover off was simple as was installing the switch. No tricks here just watch the videos and your all set to do the job

I watched the repair video on Partselect, it was very informative. In the video the agitator lifted right out easily, I was not so lucky. It took me and another gentleman about 4 hours to get the thing out. I watched other videos on ideas to remove, still no luck. Finally I cut the strap off of a carry all bag and was able to get it in around the agitator and slide it under it. After getting it under the agitator we were able to pull up on it and get it loose.
The rest of the repair was simple, cleaned everything, installed new part, and now washing machine is working like new again.

My spin cycle was running, but spinning slowly and not drying my clothes. The agitator spun quickly like normal, but the basket did not spin fast. It seemed like something was slipping. I checked the belt, but it seemed fine and it was less than a year old. I was afraid that the transmission was going, but there wasn't any grinding sound of gears. Luckily the hub part description said that this could fix the slow Spin cycle. Over all the repair was easy, but pulling the agitator off was very difficult. I've got a strong grip and patience and after about 10 - 15 mintues of yanking on the agitator it came off. Don't try to use pliers as it will damage the plastic agitator. Replacing the hub drive and reassembly went very smoothly. The old hub drive wore out because it is plastic and connects to the metal drive shaft from the transmission. After years of torque, the hub will eventually strip out. Sooner depending on your usage and heavy duty cycles. In case you don't know, your machine might have the service manual in it on the inside of the body taped to the side. Mine helped me run through some troubleshooting steps and component tests to pinpoint to problem. Thanks Parts Select!

Cold and hot water valve .easy as pie.

I watched the video and did exactly what they said to do. It was really easy. The key to the success was in the parts that were mailed to me it had a separate piece of paper telling you to "reset" the washer after doing the repair. I missed this when I watched the video. That was a critical part of the repair which required no tools to accomplish.
I have done 6 loads of wash and the washer has not made any crazy noises and hasn't moved!

I did the repair just as the video showed, and had no problems at all.
the hardest thing I had to do was to move the washer out to where I could get to the back of the machine.
Due to the help of the sales rep and the video the repair was very easy

Thanks
Louis

Turn off the water at both the cold and hot. May need an bucket to catch any water left in the lines. Then unplug the washer to kill power of course...Taking off the 10 or so small screws in the back metal cover will get you started. The tricky part is getting the clips off the back top where the knobs are. You will have 2 plastic clips and 2 metal clips, 1 on each side. Take a flat head and ease them up and out....careful not to break them! You can pull the whole control panel away from your work area. Once you have full accuses to the valves its self, it is held in by 2 screw on the top inside a slot. You can now unplug the pigtail harness. Repeat the process in reverse to get it back together and the job is complete. 30 to 45 minutes Max.

When to PartSelect Web site, used their trouble shooting guide, Used their advice, which was to replace the actuator. bought and installed the actuator which took around 20 minutes or so. washer started working fine after replacing. Thanks to the website I save a lot of money. Thanks PartSelect

Research showed it was the transmission and the actuator . Parts were super easy to install and it solved the issue 100%

PS - I put some light lithium grease on the transmission and it’s quieter than it was when new

I unscrewed the top panel of the washer. I lifted up the top and used the pint scrapper to loosen up the lid switch and slid it out. I pulled the switch wiring harness out of the rear top of the washer. I slid the new lid switch and wiring harness back through the opening and secured the switch in place. Screwed it back in place. Took less than 15 minutes. I followed the instructions on the video, easy peasy lemon squeezy.