MVWC360AW0 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brian from GREENBRIER, AR
- Parts Used:
- WPW10006384, W10721967, W10528947
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
wasn't cleaning very well
Went with the instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doris from CONCORD, NC
- Parts Used:
- WPW10683603
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
cold water inlet valve bad
Ordered the inlet assembly from this site. Received it the day after I received the notice it shipped. Watched their video of how to replace the part. Easy job, done in 15 minutes. Only needed a screwdriver to take the cover off the back of the washer control panel. A company wanted $400 to replace the part.
Definitely recommend the company and will use again.
Definitely recommend the company and will use again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from GREENFILD TWP, PA
- Parts Used:
- W10528947
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Wash plate spinning. Clothes not spun out.
Royal pain getting the wash plate off. I'm 6 foot 215 lbs with muscular arms( beer belly too) and I could not get it to come off. Put hay bail twine around the edge and pulled up so hard the entire machine came off the ground. Luckily I am married. Yep I pulled one end of the string and her the other and it flew off. Part select was $10 cheaper than whirlpool and was a perfect match. I might order another to have because like stated earlier I'm married. She is married to me and the washer and dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from SAN JOSE, CA
- Parts Used:
- W10404050
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Washer would not adgitate
I ordered a lid switch because the washer wouldn't agitate. Most reviews indicated that was the problem. While waiting for the part to arrive, I discovered the transmission to be of fault.I let parts select know that I no longer needed the part. Parts Select gave me an immediate refund no questions asked and before I returned the part to them. That is customer service!! I will use Parts Select for all my future purchases. I can trust a company that trusts its customers.
Joe M. San Jose
Joe M. San Jose
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from INDIAN LAKE, NY
- Parts Used:
- W10404050
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Lid wouldn't lock
Removed 5 screws on back, released 2 retention clips on front, lifted top of washer to expose lock assembly, removed 2 screws holding lock assembly in place followed electrical line back to plug behind control panel plugged new lock in, and reassembled in reverse order. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BRISTOL, CT
- Parts Used:
- WPW10006384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Belt needed to be replaced
Took the Cover off and installed belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from DUNBARTON, NH
- Parts Used:
- W10528947
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
violent basket wobble
remove basket and replace drive hub kit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PINE MOUNTAIN, GA
- Parts Used:
- 8212641RP
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Washer hoses due for replacement
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from VACAVILLE, CA
- Parts Used:
- W10440729
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Spin cycle was way out of wack, like it was over loaded to 1 side
1st watched the video, turned off the water supply, unplugged the elecrtcal cord, removed the rear top panel , screws with the nut driver , then slid the top forward about 1 inch & then lifted upwards to removed the lid assy, after taping the lid assy down so it wouldn't flip open. Then once lifted up, at the very back are 2 slots, which you can the set the top onto, then use the 2 s-hooks with a chain to support the lid assy from falling backwards and attach to the base assy.
Then you can move the tub assy away from where you need to work.in this case was replacing the upper plastic suspension rod supports, then push upwards the socket , drop in the new one, pull of on the rod assy, and hook it into the ball and drop bach into the suppprt , was able to do all 4 in no time. Then unkook and reattach all, screws, plug back in, turn on the water. And we were good to go.
All For less than $20.
Then you can move the tub assy away from where you need to work.in this case was replacing the upper plastic suspension rod supports, then push upwards the socket , drop in the new one, pull of on the rod assy, and hook it into the ball and drop bach into the suppprt , was able to do all 4 in no time. Then unkook and reattach all, screws, plug back in, turn on the water. And we were good to go.
All For less than $20.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from INDIANAPOLIS, IN
- Parts Used:
- WPW10006355
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
would not spin
online videos were great. called to order and lady was very helpful. washer is now operating normal
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from Saint Cloud, FL
- Parts Used:
- WPW10276397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Remove and replace drain pump
Unplug unit. Remove back panel. Disconnect drain hose using pliers to squeeze hose clamp. Tilt washer forward to access drain pump. Remove three screws on the pump. Unplug wire connector. Install new pump. Plug in the wiring connector. Reconnect hose. Reinstall back panel. Super easy fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristy from Lebanon, NJ
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Washer was making an awful screeching noise when agitating
I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shane from CLINTON TWP, MI
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Rinse cycle kept repeating, did not spin clothes
Spin indicator light was illuminated but machine was repeating rinse cycle rather than spinning water out of clothes. Replaced the pulley and drive coupler, thinking there was a mechanical problem. Video instructions were great but old pulley and drive coupler looked perfect so replacing them did nothing. Next I replaced the washer actuator (shifter), thinking that was the reason for no high speed spin. Easy job, as shown in the video, but it also did nothing. The problem turned out to be a failure in the control panel, probably resulting from years of vibration. Decided to stop chasing my tail and bought a new washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from Carteret, NJ
- Parts Used:
- W10440729
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
when in spin mode machine walks around the cellar
Unplugged remove hoses remove drain hose turned over on its back remove suspension Springs installed new Springs good backup connected Springs did not solve problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard E from BURKE, VA
- Parts Used:
- WPW10683603
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Water leak into washer drum
Replaced the water inlet valve. Easy install… figured it out on my own, but checked the instructional online video to make sure it was done right.
Was this instruction helpful to you?
Thank you for voting!