Models
>
MVWB835DW0
MVWB835DW0 Maytag Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Models for MVWB835DW0
Click on the best match to narrow your results.
Diagrams for MVWB835DW0
Viewing 6 of 6
Keep searches simple, eg. "belt" or "pump".
The suspension rods help to keep the tub in your washing machine stable and secure while cycling through your laundry. If your washer is excessively vibrating, moving around, or very loud when operati...
In Stock
Order now and your part arrives by Nov 19
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
No Longer Available
$71.11
If your washer isn’t filling properly or is leaking near the back, this inlet valve might be the problem. It controls how hot and cold water enter your machine during the wash cycle. With two inlets a...
In Stock
Order now and your part arrives by Nov 19
$82.21
This lid lock assembly is a safety-critical component found in many top-load washing machines. Positioned beneath the washer lid, it includes both the locking mechanism and the wiring harness needed t...
In Stock
Order now and your part arrives by Nov 19
In Stock
Order now and your part arrives by Nov 19
$87.95
This wash plate is for washers
Unplug the washer and shut off the water supply before installing this part
In Stock
Order now and your part arrives by Nov 19
$340.93
This OEM glass lid assembly fits select top-load washing machines and includes the lid lock feature. Made from tempered glass and durable plastic in a chrome shadow finish, it replaces broken or malfu...
In Stock
Order now and your part arrives by Nov 19
In Stock
Order now and your part arrives by Nov 19
In Stock
Order now and your part arrives by Nov 19
$81.17
This is a dispenser drawer assembly direct from the manufacturer and used in washing machines. This drawer is made of plastic and features the compartments for bleach, detergent, and softener, for you...
In Stock
Order now and your part arrives by Nov 19
In Stock
Order now and your part arrives by Nov 19
In Stock
Order now and your part arrives by Nov 19
Common Problems and Symptoms for MVWB835DW0
Viewing 16 of 16Shaking and Moving
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Lid or door won’t close
Fixed by these parts
How to fix it
Water Filling Issues
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Spinning Issues
Fixed by these parts
How to fix it
Locking Issues
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Noisy and Marks Left on Clothes
Fixed by these parts
How to fix it
Does not dispense fabric softener or detergent
Fixed by these parts
How to fix it
Cycle Not Advancing
Fixed by these parts
How to fix it
Draining Issues
Fixed by these parts
How to fix it
Will Not Dispense
Fixed by these parts
How to fix it
Spins slowly
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Terry from Homosassa, FL
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Violent shacking in spin mode.
Watched a video on the internet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from STARKVILLE, MS
- Parts Used:
- W11393685
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Loud grinding noise when the washer was in use.
1.) disconnect power to your washer. Turn off water supply and disconnect from the washer.
open the washer top and remove plastic cap from the wash plate
2.) using 7/16 socket, remove bolt from the wash plate. If you can't remove it with a socket , I recommend using impact wrench.
3.) remove wash plate ... Read more ( you might need to spray penetrating oil or wd40 inside the bolt hole to loosen it.
Check to make sure the wash plate gear grooves are not worn down, if they are, replace it.
4.) using your Maytag specific spaner nut wrench, remove the spaner nut from the shaft of the gear case. This should be right underneath where the wash plate was. If you can't turn it by hand , use a rubber mallet or hammer to encourage it.
5.) some people remove the wash basket at this point. I don't think it is necessary.
6.) close your washing machine. Tape the top closed to keep it from flying open. Tilt your washer back and prop it up where you have access to the underside of the washing machine.
7) remove motor rotor bolt and pull rotor off of the motor.
8.) disconnect the two wire connectors that supply power to motor. using a socket, remove bolts that are keeping motor attached to the gear case.
9.) Now that the gear case is all the is remaining on the underside, you can remove the 4 bolts that are holding the gear case to the washer. Now try to pull gear case out.
10.) if gearcase will not pull out, lower washer back to upright position. Spray penetrating oil or wd40 around the shaft of the gearcase and allow it to sit for 5-10 minutes. Using a hammer, lightly tap on the shaft of the gearcase and it should now fall out. ( you might have to apply penetrating oil again, or apply more force with the hammer.
11.) reinstall motor to new gearcase. Insert new gear case to the washer. Reinstall bolts and reconnect power supply wires.
12. ReInstall spaner nut inside the washer, reinstall wash plate.
open the washer top and remove plastic cap from the wash plate
2.) using 7/16 socket, remove bolt from the wash plate. If you can't remove it with a socket , I recommend using impact wrench.
3.) remove wash plate ... Read more ( you might need to spray penetrating oil or wd40 inside the bolt hole to loosen it.
Check to make sure the wash plate gear grooves are not worn down, if they are, replace it.
4.) using your Maytag specific spaner nut wrench, remove the spaner nut from the shaft of the gear case. This should be right underneath where the wash plate was. If you can't turn it by hand , use a rubber mallet or hammer to encourage it.
5.) some people remove the wash basket at this point. I don't think it is necessary.
6.) close your washing machine. Tape the top closed to keep it from flying open. Tilt your washer back and prop it up where you have access to the underside of the washing machine.
7) remove motor rotor bolt and pull rotor off of the motor.
8.) disconnect the two wire connectors that supply power to motor. using a socket, remove bolts that are keeping motor attached to the gear case.
9.) Now that the gear case is all the is remaining on the underside, you can remove the 4 bolts that are holding the gear case to the washer. Now try to pull gear case out.
10.) if gearcase will not pull out, lower washer back to upright position. Spray penetrating oil or wd40 around the shaft of the gearcase and allow it to sit for 5-10 minutes. Using a hammer, lightly tap on the shaft of the gearcase and it should now fall out. ( you might have to apply penetrating oil again, or apply more force with the hammer.
11.) reinstall motor to new gearcase. Insert new gear case to the washer. Reinstall bolts and reconnect power supply wires.
12. ReInstall spaner nut inside the washer, reinstall wash plate.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from RICHMOND, VA
- Parts Used:
- W11259006
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Broken lid frame at left hinge.
Raised lid to remove two Torx head screws from each hinge. Lid will then lift off of hinges. Installation of new lid was the reverse of the removal procedure. It is best to install one hinge to the lid by removing that hinge from the washer. The lid can then be installed by inserting that hinge into it's spot and then over the other hinge
... Read more
. Install the hinge screws into the second hinge and the job is complete. The lid now closes properly allowing the automatic lid lock to function properly.
Read less
Was this instruction helpful to you?
Thank you for voting!