Models
>
MVWB835DC0
MVWB835DC0 Maytag Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for MVWB835DC0
Viewing 6 of 6
Keep searches simple, eg. "belt" or "pump".
$5.42
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
Order within the next 44 mins and your part ships today!
In Stock
Order within the next 44 mins and your part ships today!
In Stock
Order within the next 44 mins and your part ships today!
$128.14
This wash plate is for washers
Unplug the washer and shut off the water supply before installing this part
In Stock
Order within the next 44 mins and your part ships today!
In Stock
Order within the next 44 mins and your part ships today!
In Stock
Order within the next 44 mins and your part ships today!
In Stock
Order within the next 44 mins and your part ships today!
In Stock
Order within the next 44 mins and your part ships today!
$25.32
This lid hinge is a genuine OEM replacement part for your washing machine. This hinge is for the left side of your lid, although it is a good idea to replace btoh hinges at once. The hinge holds up th...
In Stock
Order within the next 44 mins and your part ships today!
In Stock
Order within the next 44 mins and your part ships today!
In Stock
Order within the next 44 mins and your part ships today!
In Stock
Order within the next 44 mins and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for MVWB835DC0
Viewing 6 of 6Leaking
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Lid or door won’t close
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Water Filling Issues
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Delmar from EAST TROY, WI
- Parts Used:
- W11244231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
replaced drain hose that was missing
slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from MAYNARDVILLE, TN
- Parts Used:
- W11393685
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer making noise on spin cycle
Removed two screws on back of lid to raise top removed tub one bolt and one spanernut pulled tub lowered top reinstalled screws laid washer down to get to bottom of washer unplugged wiring removed four bolts pulled gear box and motor removed motor from gear box installed motor on new gear box reassemble washer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dewey from BURKBURNETT, TX
- Parts Used:
- W11165546
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
washer would not fill, all 4 valve solenoid checked good.
The valve is a 4 solenoid valve, which has Temp. sensor molded into the valve body mixer center outlet. No mention of it in the troubleshooting. it has a 2 pin plug. it was shorted zero ohms.
New one measure open infinity. I also purchased the control module as the troubleshooting said to if solenoid checked good which all 4 rea ... Read more d 1310 ohms , i purchased and replaced control module, no help. the guide is outdated for these new high tech washers. If this happens again. I will just unplug the 2 pin plug on bottom of valve assembly. By the way the 2 clips that hold the washer top in place are very difficult to remove and re install.
New one measure open infinity. I also purchased the control module as the troubleshooting said to if solenoid checked good which all 4 rea ... Read more d 1310 ohms , i purchased and replaced control module, no help. the guide is outdated for these new high tech washers. If this happens again. I will just unplug the 2 pin plug on bottom of valve assembly. By the way the 2 clips that hold the washer top in place are very difficult to remove and re install.
Read less
Was this instruction helpful to you?
Thank you for voting!