Models > MVWB750WQ1 > Instructions

MVWB750WQ1 Maytag Washer - Instructions

Jump to:

All Instructions for the MVWB750WQ1
61 - 75 of 92
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
James from Carrollton, TX
Parts Used:
WPW10119828, WP8563964
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Hinge pins were sheared off
I removed the screws holding the broken hinges and put the new hinges on. It only took a few minutes.
Was this instruction helpful to you?
Thank you for voting!
Customer:
tntsplace.com from MCALLEN, TX
Parts Used:
WP8563964
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Old hinge broke, door did not open and close right.
I removed the screws from old hinge that had broke. The piece came right out with ease. I slid the new hinge in to the hole that it went in. No struggles with ease. Lined up the screw holes and put the screws back in. Finished! Works like a charm.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jacob from Glennville, GA
Parts Used:
W10536347
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
washer would not drain water
need to get washer turned on side where you can work underneath the machine. This job is alot easy if you get where you can see good and have plenty of room to work. You have to unhoook the wire from the old pump and then take the two mounting screws off from there you unhook each hose by squeezing clamp together and sliding backwards away from pump. A pair of needle nose pliers can make this process easier if the clamps are turned in an hard to get to position. You mount the new pump the same way as taking off the damaged pump. Take a screwdriver to help you slide the clamps up onto the new pump makeing sure the sleeves are completely over the new pump fittings and the clamps are slid up evenly, so you want have any leaks. Then replaces wiring harness and mounting screws.
Was this instruction helpful to you?
Thank you for voting!
Customer:
richard from asheville, NC
Parts Used:
W10536347
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
replaced leaking pump
Easy repair. Went to You Tube and saw PartSelect video. The best instructions...should make a link from parts page to video of install. Also replaced Heat element on Dryer. Watched video first.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ronald from Demopolis, AL
Parts Used:
W10536347
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
Washer making noise down close to bottom of machine.
First unplug electrical, disconnect all hoses. If there is a large volume of water left in the machine you need to get it out.Pull machine out so you will have room to work. Lay machine front face down. Remove drive belt, inspection cover.Take the hose clamps back up the hose,remove hoses from pump. Remove the three screws that hold the pump in place.Replace pump, take steps back as you removed the pump to restore machine to operation.Total time 45 min. I am old and slow.
Was this instruction helpful to you?
Thank you for voting!
Customer:
CARROLL from HENDERSONVILLE, NC
Parts Used:
W10536347
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Hole in casing of drain pump due to loose nickle being pulled into pump - No screen in inlet to pump
Pulled back off of washer. Removed Spring clamps from inlet and outlet of pump housing. Removed hoses. Removed three screws holding pump in place. Disconnected electrical plug connector. Reassembled in reverse order. Note: new pump had no isolators and pump motor cover looked like a rat had chewed it up; however, motor, pump, and hoses appeared to be new. Put it on without the motor cover and it works. Epoxied the old pump housing to seal it up and now have a spare.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles from Houston, TX
Parts Used:
WPW10419333
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set
machine gives uneven load alarm and f51 error code
Tilt the machine over to access the bottom I rested it on a dolly.remove the rotor with an allen wrench .then rmove the 4 bolts on the stator .then lift it off the main shaft and unlug the sensor wires . just reverse the process to install the new one (be sure to allign the arrows on the sensor and the stator when reistalling. I wish i could say this solved my problem .my machine runs untill the spin cycle then it starts shaking and gives the uneven load alarm again.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Elijah from Point Hope, AK
Parts Used:
W10193886
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Socket set, Wrench (Adjustable)
UL flashes, will not spin, really loud,& black spots under washer
We ordered the outer tub & bearing and now the washer works like it was brand new.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JESUS from PORT ARTHUR, TX
Parts Used:
WPW10619844
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
did not work
reemplace the lid lock assembly
Was this instruction helpful to you?
Thank you for voting!
Customer:
Neil from Onalaska, WI
Parts Used:
W10536347
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench set
Water would not drain
I read the directions on this web site and was able to install the new drainage pump in about 30 minutes. I suprised myself. Thanks.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donald from Ormand Beach, FL
Parts Used:
W10193886
Difficulty Level:
Easy
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
noisy
Removed old tub assembly and installed new tub. Job took a little longer due to first new tub arrived damaged and I had to partially reassemble machine temporarily until second tub arrived.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donald from Hedgesville, WV
Parts Used:
W10435302
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Bearing's were shot and seal leaked water every where.
Replaced bearings, seal and new shaft. Washer never sounded this good, well I can't even tell it's running now. Very quiet. Just watch all the you tube vids on replacing seal and bearings and you shouldn't have any problems !
Was this instruction helpful to you?
Thank you for voting!
Customer:
Harley from Flower Mound, TX
Parts Used:
W10435302
Difficulty Level:
Easy
Total Repair Time:
More than 2 hours
Tools:
Screw drivers, Socket set, Wrench set
Bearings noisey
Followed instruction sheet. Removd tub assembly, Laid, washer on side, removed motor and necessary wiring, removed drive shaft, bearings and seal assembly, cleaned all areas, installed new parts. Reassembled.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Raymond from League City, TX
Parts Used:
W10435302
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Top bearing frozen and had to be cut out
Using instructions that came with parts and google and utube
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brian from Eagle Mountain, UT
Parts Used:
W10364988, WPW10233462
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
The recirulation pumps was making a really rough noise when running. water would not enter into the washer when started
To start out, I ordered two parts for a washer, a water valve and a recirculation pump. I found out that one of the solenoid switches went bad on the valve body. I tried to find just this switch but found out that you have to buy the whole valve assembly just to get one of the switches. The recirculation pump was making a really bad noise when it would run. The problem with the pump, the impeller that pushes the water out of the pump was in pieces in the pump head housing. I paid to rush the delivery so the washer was not unusable for every long. The parts showed up as planned with one problem. One of the solenoid switches was not attached to the valve body, it was broken off of the valve body. I called the service number that was on the packing slip. The lady I spoke with about the broken part apologized and quickly placed another order with the same part. Down side was she could not get it sent out that day because it was late afternoon on a Friday and the shipping department was closed. So the earliest I would receive the part would be the following Tuesday. She did refund my rush delivery cost, so i paid for just standard delivery. I had the recirculation pump on the Friday I was hoping for but still could not get the washer running until I received the water valve the following Tuesday. I told the lady I understand her hands are tied about shipping the part out that day, Since there was nobody there to ship it. I also understand that sometimes things do get broke in transit. The part was delivered on the following Tuesday as promised. I opened up the package to inspect it. This time the part inside the package was packed a little different and a little more secure. I was glad the service department was easy to deal with, very respectful and willing to correct the problem. All and All The repair went really well, had no problems installing the parts what so ever. (To make things a little easier to remember where they go)Leave the old wire harness intact with the old water valve when you remove it. Once the new water valve is install you can reference how to install the new wire harness from the old water valve. The pump had 3 screws and 2 hose clamps to remove it. It is easier if you can tilt the washer forward (just a little) to change out the pump. You can change out the pump without tilting the washer, just easier if tilted. I would order from partSelect again. I would recommend my friends and family to order from partSelect.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the MVWB750WQ1
61 - 75 of 92