MVWB700VQ0 Maytag Washer - Instructions

To start out, I ordered two parts for a washer, a water valve and a recirculation pump. I found out that one of the solenoid switches went bad on the valve body. I tried to find just this switch but found out that you have to buy the whole valve assembly just to get one of the switches. The recirculation pump was making a really bad noise when it would run. The problem with the pump, the impeller that pushes the water out of the pump was in pieces in the pump head housing. I paid to rush the delivery so the washer was not unusable for every long. The parts showed up as planned with one problem. One of the solenoid switches was not attached to the valve body, it was broken off of the valve body. I called the service number that was on the packing slip. The lady I spoke with about the broken part apologized and quickly placed another order with the same part. Down side was she could not get it sent out that day because it was late afternoon on a Friday and the shipping department was closed. So the earliest I would receive the part would be the following Tuesday. She did refund my rush delivery cost, so i paid for just standard delivery. I had the recirculation pump on the Friday I was hoping for but still could not get the washer running until I received the water valve the following Tuesday. I told the lady I understand her hands are tied about shipping the part out that day, Since there was nobody there to ship it. I also understand that sometimes things do get broke in transit. The part was delivered on the following Tuesday as promised. I opened up the package to inspect it. This time the part inside the package was packed a little different and a little more secure. I was glad the service department was easy to deal with, very respectful and willing to correct the problem. All and All The repair went really well, had no problems installing the parts what so ever. (To make things a little easier to remember where they go)Leave the old wire harness intact with the old water valve when you remove it. Once the new water valve is install you can reference how to install the new wire harness from the old water valve. The pump had 3 screws and 2 hose clamps to remove it. It is easier if you can tilt the washer forward (just a little) to change out the pump. You can change out the pump without tilting the washer, just easier if tilted. I would order from partSelect again. I would recommend my friends and family to order from partSelect.

First off always remember to empty all pockets, coins etc ruin pumps.shut off water supply, unhooked water lines and drain into pan.tilted machine forward so i could work on pump which is located lower left. drain pan under pump area, removed 2 rubber water hose's 3 5/16 screws with nut driver. Very carefully un clip rear of housing and removed wire harness. installed new pump

PLASTIC motor housing gets hot and become loose. causing bearing to spin and make noise . Replaced motor that was quick and simple by removing 3 screws and 2 hose clamps , pluged up motor and begain washing again with no problem . Just wish motor housing was not plastic .

Went to youtube.com and watched the video that took you step by step in replacing the lid lock assembly.

It was not easy but I dit my sell

Tilt the machine over to access the bottom I rested it on a dolly.remove the rotor with an allen wrench .then rmove the 4 bolts on the stator .then lift it off the main shaft and unlug the sensor wires . just reverse the process to install the new one (be sure to allign the arrows on the sensor and the stator when reistalling. I wish i could say this solved my problem .my machine runs untill the spin cycle then it starts shaking and gives the uneven load alarm again.

I read the directions on this web site and was able to install the new drainage pump in about 30 minutes. I suprised myself. Thanks.

We ordered the outer tub & bearing and now the washer works like it was brand new.

reemplace the lid lock assembly

The rod kit fixed the issue. I cant really explain how I did it, because I dint know if I did it the right way.

Followed instruction sheet. Removd tub assembly, Laid, washer on side, removed motor and necessary wiring, removed drive shaft, bearings and seal assembly, cleaned all areas, installed new parts. Reassembled.

Replaced bearings, seal and new shaft. Washer never sounded this good, well I can't even tell it's running now. Very quiet. Just watch all the you tube vids on replacing seal and bearings and you shouldn't have any problems !

Removed old tub assembly and installed new tub. Job took a little longer due to first new tub arrived damaged and I had to partially reassemble machine temporarily until second tub arrived.

Pulled back off of washer. Removed Spring clamps from inlet and outlet of pump housing. Removed hoses. Removed three screws holding pump in place. Disconnected electrical plug connector. Reassembled in reverse order. Note: new pump had no isolators and pump motor cover looked like a rat had chewed it up; however, motor, pump, and hoses appeared to be new. Put it on without the motor cover and it works. Epoxied the old pump housing to seal it up and now have a spare.

Our washer wasn't really working, we called a tech to diagnose our problem, he charged us $35 to let us know that we had a suspension problem, he promised to call us back next day with the estimate for the repair, he never did. So I decide to search, I found a video showing exactly how to do it, it was a very easy, and simple process that I decide to order the parts my self. The parts were delivered to my door in 24hrs. I installed the parts in less than 45 min, and now our washer is working like new again!!!

Thanks guys.