MAT20MNAWW0 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bernard from ARIZONA CITY, AZ
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Gear stripped on main spline
Followed detailed instructions which were supplied with the parts. It was easy and my machine is working great with no issues. Also I just didn’t get the main drive pulley, all new parts came for the bottom end, great service and excellent parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clinton from OKLAHOMA CITY, OK
- Parts Used:
- WPW10131112, WP3949550, W10772621
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Agitator was not turning. Dogears were worn out
First need to remove cap on Agitator. Inside there is a washplate bolt. Remove bolt. Old Agitator will slide up. Pull washer off stem. Clean grooved stem very well. Use some sort of lubricant on stem. Slide new Agitator on to stem. Part will be very snug as metal and plastic do not mix well. (Lubricant needed) Use board to lay flat on top. Gently tap with mallet until fully seated. Install new bolt. Run test wash. (Helps clean wash tub from any foreign substances.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TERRY from WAUKEE, IA
- Parts Used:
- W10721967
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
When the washer goes into a spin cycle, I would hear an intermittent loud clattering noise. I think the clutch teeth above (the cup part that is spring loaded) and the belted pulley's teeth below are not fully seating on each other during the spin cycle.
W10721967 Splutch Cam Kit
Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.
When I took off the 13mm nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.
Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.
Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.
Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.
When I took off the 13mm nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.
Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.
Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Staten Island, NY
- Parts Used:
- WPW10276397
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Socket set
The washer stopped draining.All the pump motor did was hum.
I drained the machine and pulled it away from the wall.Then I disconnected the drain hose and removed the back panel.Next,I removed the three screws holding the pump in place and disconnected the power plug from the motor.I then removed the short drain hose from the pump.Installation was the opposite of the removal sequence,and the machine worked fine right after I was done.The new part was identical the the old one,and the job was a snap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucas from ARKANSAS CITY, KS
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Making a loud noise for a while then stopped spinning
Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JERRY W. from CARROLLTON, GA
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
making noise when starting spin cycle
Watch video on the site and the insulation will be easy and take about 30 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tricia from HARLEYSVILLE, PA
- Parts Used:
- W10780048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Washer walking during spin cycle
Watched video and followed instructions. Removed rods from top cups, laid washer on its side and pulled them out. Put new rods thru, stood washer up and hooked them in. Was pretty easy, tube heavy but I'm 52 and I did it myself.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristy from Lebanon, NJ
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Washer was making an awful screeching noise when agitating
I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from Saint Cloud, FL
- Parts Used:
- WPW10276397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Remove and replace drain pump
Unplug unit. Remove back panel. Disconnect drain hose using pliers to squeeze hose clamp. Tilt washer forward to access drain pump. Remove three screws on the pump. Unplug wire connector. Install new pump. Plug in the wiring connector. Reconnect hose. Reinstall back panel. Super easy fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from WHITEWATER, CA
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Socket set, Wrench (Adjustable)
Not really a problem but the hardest part was moving the washer to lay on its back.
I simply followed Steve's instructions on video. Very easy repair. Washer works great, no jumping or vibrating.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from LONG BEACH, NY
- Parts Used:
- W10780048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Loud banging during spinning
Followed video provided by Part Select. Video made it look easier than it was but was very thorough and I was able to accomplish repair in less than an hour! The agitator before repair would bounce up and down when I pressed hard and let go. After repair it was much tighter!! Evidently this is a common problem with this design of Whirlpool washers!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from TEXAS CITY, TX
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
machine wobbled violently
followed video instruction that came with part. Previously watched youtube video (there are several, the low production videos are well worth viewing over the professional types). It was a breeze, other than the videos saying one person could do all four. When you get to the last rod, it is more difficult to lift the tub to insert the final rod in the round holder. I asked my wife for assistance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracy from CONWAY, AR
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
My washer was always off balance.
I used a jack to lift the tub and unhooked the rods and replaced them. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tuan from LADSON, SC
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
On Spin cycle washer jumping all over the place.
Just follow the video! Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from ARVADA, CO
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
out of balance
The info. was really helpful
Was this instruction helpful to you?
Thank you for voting!