4GMVWC400YW2 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kristy from Lebanon, NJ
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Washer was making an awful screeching noise when agitating
I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from Carteret, NJ
- Parts Used:
- W10440729
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
when in spin mode machine walks around the cellar
Unplugged remove hoses remove drain hose turned over on its back remove suspension Springs installed new Springs good backup connected Springs did not solve problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shane from CLINTON TWP, MI
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Rinse cycle kept repeating, did not spin clothes
Spin indicator light was illuminated but machine was repeating rinse cycle rather than spinning water out of clothes. Replaced the pulley and drive coupler, thinking there was a mechanical problem. Video instructions were great but old pulley and drive coupler looked perfect so replacing them did nothing. Next I replaced the washer actuator (shifter), thinking that was the reason for no high speed spin. Easy job, as shown in the video, but it also did nothing. The problem turned out to be a failure in the control panel, probably resulting from years of vibration. Decided to stop chasing my tail and bought a new washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Kalkaska, MI
- Parts Used:
- WP3949550
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
agitator broke
very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from SEBASTIAN, FL
- Parts Used:
- WP688805
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The dryer nob wasn't working the dryer knob broke off inside the unit
It was very easy to install the new parts successfully thanku parts select I will always keep using your business the representative was so helpful and understanding my problem I wish I could remember his name he was outstanding and a 100 thumbs up to him
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Enrique from Miami Shores, FL
- Parts Used:
- WP21258
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
spin cycle did not activate
Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having washer door bang shut.Took longer than expected, but each procedure was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ace from VENICE, FL
- Parts Used:
- W10205824
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
The spin cycle was very noisy & shook the whole machine.
The part we needed wasn’t pictured — nor the quantity identified. There are 4 absorbers required for full replacement. I received one absorber — 3 1/2 inches X 1 1/2 inch wide X 1/8 inch thick. Including shipping, the cost was $53.00!! Outrageous! A 10 foot roll of the same thing can be bought online for less than $20.00.
By the way, it didn’t solve the problem.
Paul
By the way, it didn’t solve the problem.
Paul
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from GOSHEN, OH
- Parts Used:
- WPW10006384, WP90767, WP3949550
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set, Wrench set
Washer will not agitate.
After changing the cogs, inner-auger clutch assembly, retaining bolt and drive belt, the washer will still not agitate. Any suggestions??
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Blaine, WA
- Parts Used:
- W10721967
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Making groaning noise in spin
Having been out of the business for quite a few years I thought that I was dealing with a direct drive machine. Thinking that it was the motor coupler. I removed the control panel and attempted to pull the cabinet froward. Not so, it had a solid cabinet, so I tilted the machine against the wall and looked under the washer finding the driven Transmission pulley loose on the shaft. The splines on the pulley were pretty well worn but I tightened the nut and it worked okay. But I ordered a pulley and replaced after it's arrival. The motor capacitor also broke it's mount off so I had to rehang it with zip ties and repaired the wires to the Capacitor, (Which BTW had about 22 gauge wire). I found it hard to believe that they would use such small wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from BARRYTON, MI
- Parts Used:
- W10528947
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
no spin
reviewed video of repair and repaired now washer works as it should . thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from DREXEL HILL, PA
- Parts Used:
- W11244231
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Replace drain hose
At first I had to position the washer so I could get access.. after having it positioned, I figured it out. Getting the clamp fastened, I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from Oviedo, FL
- Parts Used:
- WP21258
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Missing lid hinge bearing
1) Using a Phillips head screwdriver, the two screws retaining the hinge pin to the lid were removed. 2) Remove hinge pin and tilt lid slightly to gain access to bushing hole. 3)Install new bushing in hole. 4)Reposition lid. Insert hinge pin through lid and into bushing. 5)Reinstall hinge pin retaining screws and tighten.
Was this instruction helpful to you?
Thank you for voting!