4KMVWC130EQ0 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ROBERT from OXLY, MO
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Banging when in spin cycle.
I FOLLOWED THE INSTRUCTIONS IN THE VIDEO AND HAD NO PROBLEMS. It was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from OROVILLE, WA
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Extreme imbalance
This washer would not go into spin cycle without going out of balance no matter how we arranged the contents in the drum. We were looking to buy a front loader when I happened open this company with video instructions and positive comments from other people with the same issue. For the cost it was worth a try. Following the video and in less than one hour the washer was back in service. It now operates like the day we installed it new. Highly recommend this fix which should save you hundreds on a new washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Enrique from Miami Shores, FL
- Parts Used:
- WP21258
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
spin cycle did not activate
Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having washer door bang shut.Took longer than expected, but each procedure was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from GOSHEN, OH
- Parts Used:
- WPW10006384, WP90767, WP3949550
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set, Wrench set
Washer will not agitate.
After changing the cogs, inner-auger clutch assembly, retaining bolt and drive belt, the washer will still not agitate. Any suggestions??
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Blaine, WA
- Parts Used:
- W10721967
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Making groaning noise in spin
Having been out of the business for quite a few years I thought that I was dealing with a direct drive machine. Thinking that it was the motor coupler. I removed the control panel and attempted to pull the cabinet froward. Not so, it had a solid cabinet, so I tilted the machine against the wall and looked under the washer finding the driven Transmission pulley loose on the shaft. The splines on the pulley were pretty well worn but I tightened the nut and it worked okay. But I ordered a pulley and replaced after it's arrival. The motor capacitor also broke it's mount off so I had to rehang it with zip ties and repaired the wires to the Capacitor, (Which BTW had about 22 gauge wire). I found it hard to believe that they would use such small wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from DREXEL HILL, PA
- Parts Used:
- W11244231
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Replace drain hose
At first I had to position the washer so I could get access.. after having it positioned, I figured it out. Getting the clamp fastened, I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from Oviedo, FL
- Parts Used:
- WP21258
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Missing lid hinge bearing
1) Using a Phillips head screwdriver, the two screws retaining the hinge pin to the lid were removed. 2) Remove hinge pin and tilt lid slightly to gain access to bushing hole. 3)Install new bushing in hole. 4)Reposition lid. Insert hinge pin through lid and into bushing. 5)Reinstall hinge pin retaining screws and tighten.
Was this instruction helpful to you?
Thank you for voting!