4KMVWC100BQ0 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from KISSIMMEE, FL
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Washer drum banging on spin cycle
Very simple repair with the kit. Old rods came out easily using vise grips locked on to rods about 10-12 inches down and pulling up. Had doubts if they were bad since everything looked good but drum bounced back several times when I shoved it down to test it earlier. New rods went in just as easy and replaced in less than 30 min. Hardest part was that I had very cramped laundry room so had to move and disconnect hoses etc. to move into larger space for repair and then move back to reconnect. Parts came quickly within about 3 days and now purrs like a kitten!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from OXLY, MO
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Banging when in spin cycle.
I FOLLOWED THE INSTRUCTIONS IN THE VIDEO AND HAD NO PROBLEMS. It was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenda from FUQUAY VARINA, NC
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Agitator doggs wore out
Followed youtube video. Great instruction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- roger from Delanco, NJ
- Parts Used:
- WPW10072840, 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
upper agitator not spinning
After removing the pressed in cap inside the agitator i removed it from the machine with a socket wrench. Then it did not take long to figure out that the two peices snapped apart. then one look at the cogs (referred to as dog ears) i knew they where stripped and where the problem. Icanceled the service call and order the parts myself from this site. So it was very easy and i'm not sure how much money i saved but the bragging rights went along way with the wife, Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from WEST LIBERTY, IA
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Agitator was not turning properly; soap left on clothes. The teeth on the agitator dogs were worn off.
Gently pry top of agitator off with small flat-blade screwdriver. Using the square end of a 1/2-inch socket extension, unscrew the plastic center "nut." Lift agitator off, remove center cone that holds the dogs, slip the retainer ring off, remove the worn dogs and replace. (Great opportunity clean the soap scum off the agitator!) Reverse the process to complete the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jose from lake forest, CA
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
agitator wasn't moving
first remove the cap on agitator(softner),then pull out inside cap (small cover inside),loose bolt in center (you need a 7/16 socket with a long extension) after that pull up the whole assamble out of the washer tub,hold bottom part and pull up agitator ,turn up side down to take out the cogs and holder, replace with new ones and go back on the instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Depeturie from Madison, AL
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Top of Agitator would not rotate
1. Lift the softener dispenser up and out
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spin the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!
This also gave me a chance to clean the agitator thoroughly!
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spin the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!
This also gave me a chance to clean the agitator thoroughly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KENNETH from HAUGHTON, LA
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
agitator stopped working
Go to youtube and watch how to repair washing machine agitator. It is so easy. did the repair. Now it works, less than $20.00 to fix. Now I don't need to buy a new washing machine. Maybe it will make it another 15 years.....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from UNIONTOWN, OH
- Parts Used:
- 80040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitation ceased
After a quick Google search I determined how to pull off the softener dispenser and top cover. Removed one bolt and pulled agitator out and apart.. Anyone who has used a socket set can do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Corvallis, OR
- Parts Used:
- WPW10072840
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The cap thingy seal broke and splattered fabric softener.
I pulled out the old cap with my hands and jammed the new thingy into place. The lady of house did the repair. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Surfside Beach, SC
- Parts Used:
- 80040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
agitator would not turn
Pop the top off the agitator, remove the bolt, pull off the agitator, pull out the part holding the cogs (dog ears),remove and replace cogs, reassemble. Works great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathon from LOCKPORT, KY
- Parts Used:
- 80040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Plastic gears wore down not allowing top half of agitator to spin
Popped off top of softener cup. Pulled out screen. Used nutdriver to back out the only bolt holding the agitator on. Pulled it off popped out plastic "gears" and popped new ones in. Put back in reverse order. Done in 5 minutes....worked perfectly! Easy!!! Thanks !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from LANGHORNE, PA
- Parts Used:
- 80040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
top agitatior was slipping
from start to finish was about 10 minutes. used screwdriver to pop off top cap of agitator. used ratchet with small extension to take out bolt for agitator. removed agitator, placed it on ground for leverage and pulled off top agitator. carefully observed old directional cogs. flipped top agitator upside down removed old worn out/ broken plastic cogs. replaced them with the new ones. hard to screw up they only install one way. kept top agitator upside down and put rest of agitator back on. flipped it right side up and pressed down hard for secure fit. placed agitator back in washer. reinstalled bolt. placed cap back on and was finished...25 year old washer working like new. $2.80 not including shipping...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eldon from Liberty Lake, WA
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Top part of agitator quit agitating in one direction.
First, I removed the (3) piece softener cup from the top of the agitator.
Then I removed the bolt from inside the top of the agitator.
The agitator drive assembly lifts out of the lower agitator.
A flanged plastic snap ring holds the (4) drive dogs into the drive assembly.
Use a small screwdriver to remove the snap ring.
Replace the (4) drive dogs, and reassemble in reverse order.
As far as repairs go, this one is really easy.
Then I removed the bolt from inside the top of the agitator.
The agitator drive assembly lifts out of the lower agitator.
A flanged plastic snap ring holds the (4) drive dogs into the drive assembly.
Use a small screwdriver to remove the snap ring.
Replace the (4) drive dogs, and reassemble in reverse order.
As far as repairs go, this one is really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from Greensboro, NC
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
would not agitate
Removed the top on the agitator. Then removed the screw with a wrench. then I removed the cam and replaced each Directional cog the way they came out. Then I replaced the cam. Tightened the screw on the agitator and replaced the top. Turned the machine on and It started agitating like it was suppose to.
Was this instruction helpful to you?
Thank you for voting!