4KMVWC100BQ0 Maytag Washer - Instructions

I used a nut driver to remove the screw that held the to part of the agitator onto the bottom part. I then took out the worn out directional cogs and replaced them with new ones and re-assembled the agitator and was back in business. The agitator now works the way it should. Easy fix. The only negative part of this experience was that the shipping was twice as expensive as what the parts cost. Very fast shipping from PARTS SELECT .

First, I unscrewing the single bolt which keeps the two part agitator in place (agitator bolt). Second, I pulled the entire agitator out from the machine. third, I then seperated the top and bottom parts of the agitator. forth, I removed the old worn out "Agitator Direction Cogs". Fifth, I then inserted the new Agitatpr Direction Cogs"s. Six, I reassembling the top and bottom parts of the agitator. Seven, I reinstalled the reassembled agitator back into the machine. Eight, after inserting and tighting up the agitator bolt with a socket rench, and tured the machine on, it work like it was new again. .

Fabric softener dispenser simply lifts off the top of the agitator. Then, a flat head screwdriver, tucked anywhere under the edge of the cap, lifts/pries it off. Then drop a 1/2" drive extension(no socket as it simply is the extension itself) into the plastic "nut" and remove it while holding onto bottom of agitator with your other hand. Lift it out, replace the cogs and reverse for reassembly. Total time less than 5 minutes, including shipping was $10.50 for cogs - repair #4 completed thanks to the fine folks at PartSelect! PS - part arrived at my door less than 24 hrs after ordering it even tho I requested 2-3 day shipping.

The repair was very simple. I removed the agitator cap with a small screw driver, removed the retainer screw with a socket set tool. I removed the top agitator, lifted the cam and removed the old worn directional cogs installed the new ones. I reassembled the agitator. All of 10 minutes.... Very easy

very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast

First I came to this web site and discovered some directions from other customers. I then followed those directions to disassemble the agitator. I removed the softener cup by pulling up on the blue plastic retention ring. I then used a flat head screwdriver to remove the plastic cap by placing the screwdriver into the slot on the side and prying it off. Next I used a 3/8 socket and extension to remove the bolt which holds the agitator to the shaft. After the bolt was removed I pulled up on the agitator and removed it from the washing machine. To remove the upper section of the agitator, I placed it on the ground and holding the base with my feet, I pulled on the upper section. I then removed the dog ears, verifyed the problem and ordered the parts (dog ears). The parts arrived in less time than promised, were installed in about 5 minutes and I was back to doing laundry. When you reassemble the agitator, turn it upside down to install the dog ears so they do not fall out.

Removed the agitator with a socket wrench and replaced cogs as directed in repair video.

First I removed the pop off cap at the top of the spiral shaped top agitator. Then reach down inside and pry off another pop off water tight cap exposing a 7/16 or 1/2 inch nut. A deep socket would probably be easiest but I didn't have one so a nut driver and luck got it unthreaded- it was pretty tight and yoiu have to hold the agitator from spinning while you unthread. Then the upper agitator asslembly lifts out and the cog assembly falls apart but it's only like 3 or four housing pieces and it only goes together one way to hold the four new cogs in place. reassemble and the machine works great again

I took out the fabric softener dispenser, then pulled of the plastic plate. There is 1 big bolt that has to be unscrewed in there. After that gets unscrewed, the whole agitator will pull out of the washer. I put the agitator on the ground, stepped gently with both feet on th bottom (mostly flat part). then I pulled on the top cylinder part, and the 2 parts separated. There is a little disk in the cylinder part that pops out. remove the top and replace the cogs. then put the disk back together. Push the two big main parts of the agitator back together...snap the disk back in and put the whole agaitator back in your washer. pop it back into place and screw in the bolt.....DONE! I have to replace these cogs about 1ce a year...it costs me about $5 and 15 minutes...but it keeps my waher running great!

Very easy repair. Popped off the top cap on the agitator with a flat head screwdriver. Then took a half inch drive socket set with the extender and removed the assembly where the cogs were housed. Inserted new cogs, put it all back together and the thing agitates like new. Simple. Saved huge dollars.

Removed the fabric cone from center of agitator pop out the plastic cover inside, remove bolt in center pull on agitator, remove cam holder and replace cams.
repeat process to re assemble

disassembled two halves, cogs just sitting there, replaced, re-assembled

We took off softner cap and then took off the agitator with a nutdriver and then pulled the top off and the central agitator that the cogs were in pulled it out took the cogs out and replaced them with the new ones . Then we put the agitator back on and tightened the nut and replaced the softner cap and we were all done.

Removed fabric softener dispenser. Inserted medium flathead screwdriver into slot on side of cover that is on agitator and pried off. Used socket wrench, socket and extension to unscrew bolt inside agitator. Lifted out and slid off plastic ring holding agitator cogs (cogs will fall right out so make sure you check to see how they're in). Replaced cogs in the same direction they came out. Very simple!!

Removed top portion of agitator to expose the nut which held it to the shaft and removed the nut with a socket and ratchet. Removed the entire agitator and carefully took apart the plastic part which held the old directional agitator cogs (4 of them) and removed them and replaced with the new ones which I had ordered. I then reassembled the agitator and dropped it in place and fastened & tightened the one nut which I had removed earlier. The entire process probably took about 10 minutes and we immediately tried the washing machine and observed that the top portion of the agitator was turning exactly as it was supposed to and I am extremely pleased that I was able to make the repairs myself. This was a very pleasant process and I would highly recommend your business to my friends and relatives. Thank you very much for your efficient help.

Sincerely,

Ken Lancaster