7MMTS0520WW0 Maytag Washer - Instructions

Looked at the repair instructions on your web site and it made the repairs simple and easy.

Old machine and vibrations are still there but weaker. Seemed to turn counter clock wise. Put a 4x4 board behind in order to stop the twisting, and keep hoses safe from vibrating and causing wear. Stays fairly stable now.

Watched a video

Watching videos identified what parts to purchase.
Once identified - WATCH EACH PARTS VIDEO (again).
Lessons learned:
1) better to NOT tilt the washer
2) watch (more than once) and learn from the videos
3) must difficult step was loosening the tub retaining nut without having a spanner wrench (used a hammer and a short / wide blade screwdriver)
4) ended up being the tub support was not sitting properly in the suspension plate
5) cleaned and changed parts while apart
6) running as good as new

Thanks!!

1. Watch a video on installation, there are many on the internet.
(unplug the washer)
2. remove the screws on the back of the control panel to lift the control panel out of the way.
3. use a flat head screwdriver to remove the clips that hold the cabinet to the back panel.
4. disconnect the lid switch from the control panel by removing the clip that connects them at the top of the cabinet.
5. tilt the cabinet forward to remove it.
6. use a flat head screw driver to remove the two clips that hold the water pump to the motor and swing the water pump out of the way.
7. use a nut driver to remove the shipping screw that holds the clips on to the motor.
8. disconnect the wiring harness from the motor
9. remove the two clips from the motor with a flat head screwdriver and remove the motor
remove the three prong coupler and rubber gasket from the old motor and put them on the shaft of the new motor
10. remove the 4 rubber pads from the old motor and slide them onto the new motor.
11. insert the new motor into the washer aligning the prongs of the coupler.
12 reassemble the washer in reverse order of disassembly
(the shipping screw does not need to be reinserted into the spring clip that holds the motor)

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

The switch just snapped out of the holding section and the new part was snapped back into its place. He put the top section back on and it worked! Being a woman not knowing anything about repairing machines, I thought it went very well. I just googled my problem with the washer, it sent me to this site saying what they thought was the problem, I live chatted with someone and they confirmed the solution. I ordered the part and it came in 2 days and my husband fixed it. And now I have a working washer again. Thank you for your site. Anne

I decided to order the part and attempt to install it. Actually was easy. Took my time and maybe took 90 minutes. Works great.

Same as described on your video. Very simple

Ordered and replaced the sensor. Fairly simple. Washer runs good now. Thank you!

Unplug the washer. Used flat blade screwdriver under each end of the control housing on top of the machine. This popped the spring clips and allowed the control housing to be lifted up and rotated out of the way. Once out of the way, lift clip on wiring harness to lid switch, then pull the harness off. Use nutdriver to remove screw holding ground wire in place. Open lid of the machine. Pinch tab on back of the lid switch and rotate the switch up and out of the machine. Insert the new switch in the same manner, making sure that the machine lid remains open until the switch snaps into place. Attach ground wire using screw removed earlier and nutdriver. Clip wiring harness back in place. Close the lid and then rotate the control housing downward, and press on both ends to re-engage the spring clips which hold it down.

Disassembled top control console and surrounding sheet metal cabinet per the video from this site. i then used a screw driver to carefully pry up each wear pad location individually and inserted the wood wedge. to about 1 1/2 inch height. rwmoved the old wear pads and popped in the new pads one by one. Closed up the unit and tested the machine . It ran like new. No more noise or viberation

We had to take the motor off and find the part that holds the spring, took longer to fix as we are older people and took a brake after every spring. We used YouTube videos to help us I am thankful for this site and cheap prices.

The video was well made and made repair easy. I like the fact the video also showed how everything went back. The most difficult part and most time consuming for me was putting the washer cabinet or housing back on. I had a hard time lining the sides onto the slot to lock in place....the minor cut on finger sustained during the process was worth it. It saved me from buying a new washer and the whole family are happy that they don't have to wring out the clothes before putting it the dryer. Thank you!

Install new valve