7MMVWH450DW1 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Angelo from PORTLAND, ME
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
The wash cycle made a loud grinding noise when it went from filling to wash.
I put the dial to drain and and pressed the pause button for 3 seconds and it drained.
Unplugged the washer from the electrical outlet .
Shut the hot and cold water off. Disconnected and drained them.
Placed the washer on a soft mat on front side exposing the back and bottom of the machine.
Unscrew the metal cover with Philips head screw driver.
Disconnect the drain hose to a bucket or small dish tub .
Remove the belt cover with 5/8 ratchet or wrench.
Using a ratchet or wrench remove the one bolt holding the clutch in place .
Remove the two Philips head screws from the shift mechanism ( looks like clock timer,my memory is failing me right now sorry! ) .
Pull down on bottom gear after removing nut.
Push in and pull down with a flat head screwdriver on the tabs holding the collar in place above the top gear .The collar and gear and spring should come apart.
Install new parts in the same order . Reassemble make sure to use Locktite 242 on the bottom nut holding the gear.
Install belt , belt guard , cover drain hose . Stand machine back up , reconnect all hoses tightly plug machine into electrical outlet and start. Put a smile on your face because you did a great job and saved yourself some money!
Unplugged the washer from the electrical outlet .
Shut the hot and cold water off. Disconnected and drained them.
Placed the washer on a soft mat on front side exposing the back and bottom of the machine.
Unscrew the metal cover with Philips head screw driver.
Disconnect the drain hose to a bucket or small dish tub .
Remove the belt cover with 5/8 ratchet or wrench.
Using a ratchet or wrench remove the one bolt holding the clutch in place .
Remove the two Philips head screws from the shift mechanism ( looks like clock timer,my memory is failing me right now sorry! ) .
Pull down on bottom gear after removing nut.
Push in and pull down with a flat head screwdriver on the tabs holding the collar in place above the top gear .The collar and gear and spring should come apart.
Install new parts in the same order . Reassemble make sure to use Locktite 242 on the bottom nut holding the gear.
Install belt , belt guard , cover drain hose . Stand machine back up , reconnect all hoses tightly plug machine into electrical outlet and start. Put a smile on your face because you did a great job and saved yourself some money!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from INDIAN LAKE, NY
- Parts Used:
- W10404050
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Lid wouldn't lock
Removed 5 screws on back, released 2 retention clips on front, lifted top of washer to expose lock assembly, removed 2 screws holding lock assembly in place followed electrical line back to plug behind control panel plugged new lock in, and reassembled in reverse order. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from ARIZONA CITY, AZ
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Gear stripped on main spline
Followed detailed instructions which were supplied with the parts. It was easy and my machine is working great with no issues. Also I just didn’t get the main drive pulley, all new parts came for the bottom end, great service and excellent parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PINE MOUNTAIN, GA
- Parts Used:
- 8212641RP
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Washer hoses due for replacement
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BRISTOL, CT
- Parts Used:
- WPW10006384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Belt needed to be replaced
Took the Cover off and installed belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from ACUSHNET, MA
- Parts Used:
- W11385424
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
No agitation
Pop center cover off wash plate. Remove bolt. Lift off washplate. Slide retainer off with screwdriver and hammer. Slide new retainer on. Replace washplate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from WARMINSTER, PA
- Parts Used:
- W10404050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Washer would go into the cycle to rinse dry.
Replacing the part was fairly easy. However it did not resolve the problem. The spin cycle did not activate,leaving my washer full of water. We ordered another Maytag Washer. Hopefully this one doesn't break down for a long time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Blaine, WA
- Parts Used:
- W10721967
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Making groaning noise in spin
Having been out of the business for quite a few years I thought that I was dealing with a direct drive machine. Thinking that it was the motor coupler. I removed the control panel and attempted to pull the cabinet froward. Not so, it had a solid cabinet, so I tilted the machine against the wall and looked under the washer finding the driven Transmission pulley loose on the shaft. The splines on the pulley were pretty well worn but I tightened the nut and it worked okay. But I ordered a pulley and replaced after it's arrival. The motor capacitor also broke it's mount off so I had to rehang it with zip ties and repaired the wires to the Capacitor, (Which BTW had about 22 gauge wire). I found it hard to believe that they would use such small wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from BARRYTON, MI
- Parts Used:
- W10528947
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
no spin
reviewed video of repair and repaired now washer works as it should . thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from Chimacum, WA
- Parts Used:
- W10404050
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
door latch broke
Figuring out how to take the lid off was the hard part. Took out the old and replaced with new and put lid back on and rehooked up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Kalkaska, MI
- Parts Used:
- WP3949550
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
agitator broke
very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from DREXEL HILL, PA
- Parts Used:
- W11244231
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Replace drain hose
At first I had to position the washer so I could get access.. after having it positioned, I figured it out. Getting the clamp fastened, I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Lincoln, RI
- Parts Used:
- W10404050
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
would not unlock
Disassembled ,as assembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Franklin, IN
- Parts Used:
- W10404050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Lid lock would not ingague.
Removed two brackets on back top of washer that hold top secure. Pulled top forward and up off off pins located on front top of washer. Located switch removed two screws holding it in. Then removed Panel on back of top in order to get to controls and unplugged other end of switch. Then reversed procedure and waher was back in service.
Was this instruction helpful to you?
Thank you for voting!