7MMVWC355DW0 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Linda from Arnold, MD
- Parts Used:
- 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Agitator wasn't turning
I watched your video, followed the instructions, and
in 20 minutes I had a new washer! The repair man estimated the cost for repair at $150, but I didn't want to spend that much money on a 20-year-old washer, so I ordered the agitator repair kit, cost $12, and it arrived the very next day! I did exactly what the video indicated and within 30 minutes my washer was agitating like never before. Thank you so much for the video instruction, it was fantastic.
in 20 minutes I had a new washer! The repair man estimated the cost for repair at $150, but I didn't want to spend that much money on a 20-year-old washer, so I ordered the agitator repair kit, cost $12, and it arrived the very next day! I did exactly what the video indicated and within 30 minutes my washer was agitating like never before. Thank you so much for the video instruction, it was fantastic.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from Little Rock, AR
- Parts Used:
- 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Agitator would not agitate properly
I also ordered a new agitator repair kit which had almost everything. I noticed that I the kit had shorted 3 of the 4 cogs. Once the missing parts were received I removed the agitator bolt from the middle of the agitiator with a rachet and socket. Amazingly, I read the instructions and followed them accordingly. I pulled removed the agitator and removed the dogs/cogs and placed the new one in the new dogs *Making "dog gone" (pun intended) sure they were facing the correct way, by comparing them to the instructions. I carefully seated them as per the illustrations on the instructions and replaced the center bolt in. placed the cap on top and started the washer. Then I had my cup of coffee. By the way..I'm a grandmother, so if I can do it.............!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- roger from Delanco, NJ
- Parts Used:
- WPW10072840, 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
upper agitator not spinning
After removing the pressed in cap inside the agitator i removed it from the machine with a socket wrench. Then it did not take long to figure out that the two peices snapped apart. then one look at the cogs (referred to as dog ears) i knew they where stripped and where the problem. Icanceled the service call and order the parts myself from this site. So it was very easy and i'm not sure how much money i saved but the bragging rights went along way with the wife, Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KENNETH from HAUGHTON, LA
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
agitator stopped working
Go to youtube and watch how to repair washing machine agitator. It is so easy. did the repair. Now it works, less than $20.00 to fix. Now I don't need to buy a new washing machine. Maybe it will make it another 15 years.....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luu from STANTON, CA
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
No problem
That OK , easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenda from FUQUAY VARINA, NC
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Agitator doggs wore out
Followed youtube video. Great instruction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Wetumpka, AL
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
worn our Agit-dogs, agitator wouldn't pull clothes down
FIRST I printed the directions from an online DIY stie, then removed a single bolt from the center of the agitator. I dismantled the agitator, replaced the dogs, and used to printed page to help me reassemble the agitator. I then replaced the bolt. It's VERY easy, but you need the pictures to be sure you've put everything back in the correct place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from UNIONTOWN, OH
- Parts Used:
- 80040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitation ceased
After a quick Google search I determined how to pull off the softener dispenser and top cover. Removed one bolt and pulled agitator out and apart.. Anyone who has used a socket set can do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Surfside Beach, SC
- Parts Used:
- 80040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
agitator would not turn
Pop the top off the agitator, remove the bolt, pull off the agitator, pull out the part holding the cogs (dog ears),remove and replace cogs, reassemble. Works great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from LANGHORNE, PA
- Parts Used:
- 80040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
top agitatior was slipping
from start to finish was about 10 minutes. used screwdriver to pop off top cap of agitator. used ratchet with small extension to take out bolt for agitator. removed agitator, placed it on ground for leverage and pulled off top agitator. carefully observed old directional cogs. flipped top agitator upside down removed old worn out/ broken plastic cogs. replaced them with the new ones. hard to screw up they only install one way. kept top agitator upside down and put rest of agitator back on. flipped it right side up and pressed down hard for secure fit. placed agitator back in washer. reinstalled bolt. placed cap back on and was finished...25 year old washer working like new. $2.80 not including shipping...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from Greensboro, NC
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
would not agitate
Removed the top on the agitator. Then removed the screw with a wrench. then I removed the cam and replaced each Directional cog the way they came out. Then I replaced the cam. Tightened the screw on the agitator and replaced the top. Turned the machine on and It started agitating like it was suppose to.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathon from LOCKPORT, KY
- Parts Used:
- 80040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Plastic gears wore down not allowing top half of agitator to spin
Popped off top of softener cup. Pulled out screen. Used nutdriver to back out the only bolt holding the agitator on. Pulled it off popped out plastic "gears" and popped new ones in. Put back in reverse order. Done in 5 minutes....worked perfectly! Easy!!! Thanks !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Clawson, MI
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Agitator was spinning freely
Removed the fabric cone from center of agitator pop out the plastic cover inside, remove bolt in center pull on agitator, remove cam holder and replace cams.
repeat process to re assemble
repeat process to re assemble
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kitty from Erie, PA
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Agitator wouldn't turn when washing clothes.
Removed fabric softener dispenser. Inserted medium flathead screwdriver into slot on side of cover that is on agitator and pried off. Used socket wrench, socket and extension to unscrew bolt inside agitator. Lifted out and slid off plastic ring holding agitator cogs (cogs will fall right out so make sure you check to see how they're in). Replaced cogs in the same direction they came out. Very simple!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry A. from Maitland, FL
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
Agitator stopped turning with a load in it.
Pulled cap off top of agitator, loosened bolt down in center of assembly and pulled collar up with pliers.
Removed old dog ears and replaced. Need to be extra careful on direction of dog ears.
Very simple; even a cave man could do it!
Removed old dog ears and replaced. Need to be extra careful on direction of dog ears.
Very simple; even a cave man could do it!
Was this instruction helpful to you?
Thank you for voting!