7MMVWC355DW1 Maytag Washer - Instructions

disassembled two halves, cogs just sitting there, replaced, re-assembled

We took off softner cap and then took off the agitator with a nutdriver and then pulled the top off and the central agitator that the cogs were in pulled it out took the cogs out and replaced them with the new ones . Then we put the agitator back on and tightened the nut and replaced the softner cap and we were all done.

To replace the dogs that cause the ratcheting motion:

I removed the softener cup by pulling straight up. (You've probably found, as I have, that the softener cup and the bleach dispensers are problematic: the softener cup must be cleaned with every use or the old softener liquid turns to glue, and the bleach dispenser mechanism plugs and distributes bleach onto your next load, ruining entire loads of clothes.)

Then I lifted the cap covering the retaining bolt by inserting a screwdriver alongside in the square holes provided, loosening it, and lifting it out.

Then I used a socket and a very long extension to remove the retaining bolt. I lifted the agitator straight up.

The next step can be a problem: I survived it (though I did strain my back). What's required, as you can see by reading the preceding letters, is to lift sharply on the upper agitator while holding the lower agitator with your bare feet or some soft shoes. What this does, at least on my model, is to break off the tabs that are fused together over the ratcheting-dogs, which are the focus of the repair. (These tabs hold the upper and lower assemblies together, moving the dogs assembly with the lower agitator.) In my case, one of the tabs broke off a half inch below the top, but that wasn't catastrophic and I didn't lose the rest of them, so when I reassembled the two halves still snapped back together.

One problem was that when I jerked the two assemblies apart, the parts of the dogs assembly went flying. Everyone had said to make sure everything went back the same way it came apart--for me there was no way to tell what that way was, but common sense tells you which way to reinstall the new dogs; they have to catch every stroke.

To reassemble, position the dogs with the retainer cup inverted. Then hold them upside down while sliding the upper agitator down over them. This holds them in place. When sliding the upper agitator down onto the lower, make sure the slots line up and use a smooth even pressure. Snap the two halves together, bolt the agitator back into the machine, replace the cap with the large o-ring (make sure you clean and/or replace the o-ing), and reinstall the softener cup.

Et, voila! You're back in business.

I just took the bolt out of the top of the agitator which allowed me to pull the agitator straight up. Then I turned it over so the sleeve that the cogs go into could fall out. I took the old cogs out, put the new cogs in, held it upside down and lowered the agitator down onto as to not move the cogs. When it was all situated correctly I held it by the bolt as I turned it upright. Then I just lowered it back down in place inside the drum and tightened the bolt back down. Done.
The washer works just like new.

Took the cap off the agitator, loosened the nut with a wrench, and pulled the agitator out. The agitator pulled apart easily, revealing the piece containing the dog ears, which were clearly worn out. Simply replaced the dog ears and reinstalled the agitator. Piece of cake!

Removed fabric softener dispenser. Inserted medium flathead screwdriver into slot on side of cover that is on agitator and pried off. Used socket wrench, socket and extension to unscrew bolt inside agitator. Lifted out and slid off plastic ring holding agitator cogs (cogs will fall right out so make sure you check to see how they're in). Replaced cogs in the same direction they came out. Very simple!!

Removed the top on the agitator. Then removed the screw with a wrench. then I removed the cam and replaced each Directional cog the way they came out. Then I replaced the cam. Tightened the screw on the agitator and replaced the top. Turned the machine on and It started agitating like it was suppose to.

I pulled out the old cap with my hands and jammed the new thingy into place. The lady of house did the repair. Easy

Pulled up and removed the fabric softner dispenser. Then I pulled up and removed the cap barrier to have access to the screw. Removed the screw and pulled up the cloths mover. Tunrned the cloths mover over to remove the bearing cam to remove the broken agitator cogs and replaced them with the new ones. I held the bearing cam with my right hand and held the cloths mover with my left hand turning it slowly with my left hand and lightly pushing down with my right hand until the cloths mover made contact with the grooves of the shaft and it sunk down on the shaft. Replaced the screw and washer then the cap barrier , next the fabric softner dispenser. Took 10 min. to complete the job. Now my washer runs like new ! Plus, I have a happy wife!

Took off softner dispenser, took off bolt cover. Used 7/16 socket with long extension and unscrewed bolt. Pulled up on agitator and out it came. Took out directional cogs and replaced with new. Reversed procedure and I was done. Saved a lot of money by not calling a mobile repair man on this one!

Removed fabric softener dispenser. Inserted screwdriver into slot on side of cover that is on agitator and pried off. Used socket extension to unscrew bolt inside agitator. Lifted out and slid off plastic ring holding agitator cogs . Replaced cogs in the same direction they came out. Since these instructions were here on site at the time I ordered the parts, it made the job very simple and fast...the order came very fast too.

Removed top portion of agitator to expose the nut which held it to the shaft and removed the nut with a socket and ratchet. Removed the entire agitator and carefully took apart the plastic part which held the old directional agitator cogs (4 of them) and removed them and replaced with the new ones which I had ordered. I then reassembled the agitator and dropped it in place and fastened & tightened the one nut which I had removed earlier. The entire process probably took about 10 minutes and we immediately tried the washing machine and observed that the top portion of the agitator was turning exactly as it was supposed to and I am extremely pleased that I was able to make the repairs myself. This was a very pleasant process and I would highly recommend your business to my friends and relatives. Thank you very much for your efficient help.

Sincerely,

Ken Lancaster

I removed the center cap from the agitator, which then exposed an inner cap with rubber seal. These were both easily removed with no tools... just a slight pull. Then the center screw was exposed. I removed that "one" screw and pulled the upper agitator assembly off. The old dog ears literally fell right out. I simply ensured that I placed the new dog ears in the same direction as the old, which is not hard to remember because the little housing piece that holds them is molded in the angle of the ears. Putting it back in took the most time because the new ears can easily fall out. In order to overcome this I had to assemble the pieces that had been removed and carefully put them back in place. At that point I had to manage to get the screw back into position and tighten it up. I put the inner cap with seal back in place and then the agitator cap... Done! It's an old machine but works great with a simple repair. The dog ears were so inexpensive that I purchased two sets. Great site!

First I popped off the very top cap of the agitator. I then used a socket extension to access the mounting bolt in the interior of the agitator. Once the bolt was loose i pulled the agitator off and dropped out the middle piece. With this out i switched the 4 cogs with the old. I then held the agitator assembly upside down and placed the middle piece back in. The most difficult part was aligning the agitator back onto the bottom part. Screw it back in place and pop the top back on.

The repair was very easy, I took the top cap off the agitator and removed the recess bolt and pulled the agitator out of the washing machine,put the agitator on the floor and put my feet on the sides of the agitator and pulled the top haft apart,replaced the agitator directional cogs put back together work great