7MMVWC355DW1 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Janice from GREENVILLE, NC
- Parts Used:
- W10404050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
My washer lid lock light kept blinking and the washer would not start
I followed the online video, removed the old part and replaced it with the new part. My washer is working perfectly. It took about an hour to reset.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from BURLINGTON, NJ
- Parts Used:
- W10404050
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Washer lid would not release
Unplug washer. Remove 4 screws from the small plates that hold top to body of washer. Remove cover plate from back of top. Lift top from base and support it on its back. Remove lid lock mechanism. Unplug connector from its socket at the back of the lid. In reverse order install the new lid latch,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from E NORTHPORT, NY
- Parts Used:
- WPW10006384
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set, Wrench (Adjustable)
Smelled a burning odor occasionally
First, I checked the belt before ordering and then decided to order the belt, capacitor, and clutch assembly (if I needed to replace). I replaced the belt noticing the older belt came right off and new one was tighter going on. I replaced the capacitor since I had it handy and it can be known to cause this smell also. After setting washer back up and started a cycle I noticed the spin cycle would not start properly so I thought maybe the capacitor (new one) was faulty or just not the exact match even though it was said to be. I replaced my older capacitor back on and again ran cycle and it ran great. Thus I decided to send the parts which were not used. I would recommend this site as I have used them in the past before on other items. They ship fast and have a great return policy if parts not used.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from COHOES, NY
- Parts Used:
- W11481722
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Machine would stop at spin cycle
After disconnecting water lines and power, tip machine onto its back. The actuator is located under the drum. Remove the cover over the motor/ drive belt. Actuator is located by the transmission and held on by several screws. Unplug the wiring harness and remove three screws with Phillips screwdriver. Install new actuator..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from NAPERVILLE, AL
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Agitator moves freely in both directions
First I removed the softener bin by pulling it up and off, then I removed the plastic seal by pulling it up and out, then I removed the 1/2 inch bolt with a ratchet and extension, then I removed the upper and lower agitator assembly from the machine and seperated the two by putting my feet on the lower agitator to hold it to the floor and pulling the upper agitator fast and firmly.
Sitting on top of the lower agitator I found the dog ear assembly. I pulled the dog ear assembly off and removed the yellow cap and existing dog ears.
Assembly was reverse.
Sitting on top of the lower agitator I found the dog ear assembly. I pulled the dog ear assembly off and removed the yellow cap and existing dog ears.
Assembly was reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from BROOKLYN, NY
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Making loud noises.
The video you sent me was very helpful told me the exact tools I needed and how to do it.
Thank you
Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hale Center, Texas, TX
- Parts Used:
- WPW10240513
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
lid would not lock, washer would not run...
Removed old striker ( 2 Phillips head screws ) replaced with new striker with the 2 screws and was done, easy fix...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELIZABETH from HARLINGEN, TX
- Parts Used:
- W10780045
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
My tub would hit the sides of the washer during spin cycle.
Followed youtube video. The repair was easy and fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from GRAIN VALLEY, MO
- Parts Used:
- WPW10006384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
squeal and chirping while in risne / spin mode
Removed belt cover from bottom of the transmission , remove old belt, clean the pulleys ,and re install new belt. The new belt fits tighter so it did a few time to get the belt fully seated. Re install belt cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marc from HOPE MILLS, NC
- Parts Used:
- W10404050
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washer wouldn't start - Flashing Lid Light
I checked out the reviews and the recommendation of these "professionals", replaced the part easy enough when it came in. However, it didn't solve the problem. Got an actual professional to come in and see what the problem was, and they determined that gear oil was being leaked and it wasn't worth replacing.
Tried to get a refund and return the part. Was told absolutely not. The money back guarantee is a lie.
Tried to get a refund and return the part. Was told absolutely not. The money back guarantee is a lie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LADD from ARCADIA, FL
- Parts Used:
- W10780045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
When the washer would go into spin cycle it sounded like the drum was banging all four sides of the washer.
Unplugged from power, unhooked water lines.Then removed back cover and control panel and top set to the side. Rear rods very easy to do by yourself after those where done have help and tip it backwards and change out the front 2 then reassembled and hooked back up and tested. Everything worked like brand new !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PRECIOUS from LAKE CITY, FL
- Parts Used:
- W10780045
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
washer shaking and banging loudly
I was able to look up the issue on Youtube and watched a few videos and was able to complete the repair with help of my daughter. It was little hard to do but you do need gloves with a good grip when taking the rods out of the washer, but putting the new ones in was very easy.
Once I replaced the suspension rods, there was a little shaking but not like before. Very quiet now, no crazy loud banging
Once I replaced the suspension rods, there was a little shaking but not like before. Very quiet now, no crazy loud banging
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessica from MT STERLING, KY
- Parts Used:
- W10780045
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Shaking and banging around when washing
Youtube has videos. It's very simple just replace one at a time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachel from PINELLAS PARK, FL
- Parts Used:
- W10780045
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Banging during spin cycle
The installation was very easy and took me 45 minutes to complete by myself. I put the washer on two cinder blocks and then removed the lid. I started with the suspension rods that were closest to me and they were really easy to exchange. When I got to the rods in the back they were a little more difficult because there was more tension with the new rods installed. I used the old rods to hook and pull the new rods into place and it was overall very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delmar from EAST TROY, WI
- Parts Used:
- W11244231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
replaced drain hose that was missing
slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys
Was this instruction helpful to you?
Thank you for voting!