7MMVWC300YW0 Maytag Washer - Instructions

With the help of a You Tube video, which was watched first, then when the parts were delivered, the video was watched again, then we played the video back and paused it after each section was done so we could make sure we were doing the repair correct. The one thing I will mention that the video doesn't mention to do is, before taking the agitator out of the washer, put a mark somewhere on the agitator to tell you which end is the top. Just remember that the top( cap ) will be off, so that will not work. Otherwise it was a good, easy fix

Pulled up and removed the fabric softner dispenser. Then I pulled up and removed the cap barrier to have access to the screw. Removed the screw and pulled up the cloths mover. Tunrned the cloths mover over to remove the bearing cam to remove the broken agitator cogs and replaced them with the new ones. I held the bearing cam with my right hand and held the cloths mover with my left hand turning it slowly with my left hand and lightly pushing down with my right hand until the cloths mover made contact with the grooves of the shaft and it sunk down on the shaft. Replaced the screw and washer then the cap barrier , next the fabric softner dispenser. Took 10 min. to complete the job. Now my washer runs like new ! Plus, I have a happy wife!

Could be done in place, but it's easier to pull the full agitator assembly out first, and work at a table. Remove the fabric softener dispenser, then the plastic cap below (with rubber o-ring)- both pull out by hand. Reverse the now visible bolt with an extended 7/16" socket and pull the cog housing up and out, gripping with gentle pressure with pliers ( locking plastic tabs make this piece impossible to remove by hand). Once the housing is removed it's easy to separate the two halves with your fingernails and replace the cogs. I was able to reassemble everything and push it back down into the drum in about two minutes. Piece of cake- I highly recommend anyone with a tool box do this himself.

Followed youtube video. Great instruction.

That OK , easy.

The top portion of the agitator was not turning so that laundry could be drawn down in the wash tub. The problem was 4 little cogs that where worn and would not catch on a gear/cog portion of the bottom portion of the agitator. the cogs where about $10 delivered and it took about 25 min. to install (from top of washer). The old cogs, I also repaired by taking them out and using a hacksaw to redefine the grooves on them. They are still working, so I will hold on to the new parts until needed.

Very simple repair with the kit. Old rods came out easily using vise grips locked on to rods about 10-12 inches down and pulling up. Had doubts if they were bad since everything looked good but drum bounced back several times when I shoved it down to test it earlier. New rods went in just as easy and replaced in less than 30 min. Hardest part was that I had very cramped laundry room so had to move and disconnect hoses etc. to move into larger space for repair and then move back to reconnect. Parts came quickly within about 3 days and now purrs like a kitten!

I watched your video, followed the instructions, and
in 20 minutes I had a new washer! The repair man estimated the cost for repair at $150, but I didn't want to spend that much money on a 20-year-old washer, so I ordered the agitator repair kit, cost $12, and it arrived the very next day! I did exactly what the video indicated and within 30 minutes my washer was agitating like never before. Thank you so much for the video instruction, it was fantastic.

Gently pry top of agitator off with small flat-blade screwdriver. Using the square end of a 1/2-inch socket extension, unscrew the plastic center "nut." Lift agitator off, remove center cone that holds the dogs, slip the retainer ring off, remove the worn dogs and replace. (Great opportunity clean the soap scum off the agitator!) Reverse the process to complete the repair.

Followed instructions on website video.

After reading on line how others did it, it was simple. I lifted out the softener dispenser. Under that there was a plastic cap. You just lift it out - theres no fasteners holding it. It just fits snugly in place by means of an o-ring. Under that there is one bolt holding the agitator to the spindle. Loosen that and remove the whole agitator. The agitator then comes apart in the middle. Just pull the two halves apart. The only tool you will need is one socket with a long extention and a ratchet. Once apart you will see the 4 plastic cogs that spin the agitator. The teeth were worn off of mine. I simply replaced the four cogs that come as a set. None of the other parts were worn to the point of needing replacement. I now have a fully functioning washing machine that was repaired for less than thirteen dollars!

FIRST I printed the directions from an online DIY stie, then removed a single bolt from the center of the agitator. I dismantled the agitator, replaced the dogs, and used to printed page to help me reassemble the agitator. I then replaced the bolt. It's VERY easy, but you need the pictures to be sure you've put everything back in the correct place.

I took a socket and removed the agitator bolt and cover which exposed the cogs. I cold see the cogs were stripped. I changed them and everything works fine.

After a quick Google search I determined how to pull off the softener dispenser and top cover. Removed one bolt and pulled agitator out and apart.. Anyone who has used a socket set can do it.

Popped off top of softener cup. Pulled out screen. Used nutdriver to back out the only bolt holding the agitator on. Pulled it off popped out plastic "gears" and popped new ones in. Put back in reverse order. Done in 5 minutes....worked perfectly! Easy!!! Thanks !!