7MMVWX655EW1 Maytag Washer - Instructions

Unplug washer. Remove 4 screws from the small plates that hold top to body of washer. Remove cover plate from back of top. Lift top from base and support it on its back. Remove lid lock mechanism. Unplug connector from its socket at the back of the lid. In reverse order install the new lid latch,

First, I checked the belt before ordering and then decided to order the belt, capacitor, and clutch assembly (if I needed to replace). I replaced the belt noticing the older belt came right off and new one was tighter going on. I replaced the capacitor since I had it handy and it can be known to cause this smell also. After setting washer back up and started a cycle I noticed the spin cycle would not start properly so I thought maybe the capacitor (new one) was faulty or just not the exact match even though it was said to be. I replaced my older capacitor back on and again ran cycle and it ran great. Thus I decided to send the parts which were not used. I would recommend this site as I have used them in the past before on other items. They ship fast and have a great return policy if parts not used.

Our 5 year old Kenmore washing machine broke. The first symptom was that the clothes would come out completely wet. This was due to no spin cycle. The second symptom was that the washing machine had little to no agitation. The lid still locked shut, there was no odor, and you could hear the machine running.

In the event a machine does not agitate or spin, the diagnostics on this website will lead you to believe that drive hub assembly or shift actuator is the problem. The drive hub assembly is by far the more common repair (the pieces are made of plastic and are designed to wear out). If you are torn, go with the drive hub kit repair. That's what it was.

There were some surprises after carefully watching the how to video. First, the agitator in my machine was very tall and required a socket wrench extension to reach the drive hub nut. This will require two sets of hands. Second, the drive hub nut was stuck to the point where I nearly gave up. WD-40 and degreaser did not work to loosen. I ended up pouring a half teaspoon of powdered soap onto the stuck nut to get more grip on the nut. This, along with two sets of hands, got it loose. Third, calibrating machine was barely touched on in the video but this is extremely difficult, the instructions that come with the part were insufficient, and the videos on the internet are not that good. In the end, I'm not sure that the machine ever calibrated. In essence, the machine is re-calibrated by turning the switch in a specific sequence of right to left. Lights are then supposed to flash. This never did anything. I ended up opening and shutting the lid 10 times in 10 seconds as this was allegedly a way to recalibrate.

Note: 2018 and later washing machines suck because of California and the federal government rules and pressure to make them "green". Well, they don't work that well anymore as a result. Keep this in mind when you vote.

The video you sent me was very helpful told me the exact tools I needed and how to do it.
Thank you

Thought we needed a new shift actuator but after getting the parts and starting the replacement noticed the capacitor had come loose and was banging around under the washer. Found there was a little wire to the shift actuator that was cut probable from the capacitor being loose. spliced the wire back together and replaced the capacitor but not the shift actuator and its been working great. was an easy fix and easy to get to. Didn't need the maytag man when we can get parts from here.

DIY'er working on a Maytag Centennial type washing machine should be aware that replacing a a transmission or agitator due to worn out splines is only half a job done well. I originally replaced my transmission due to worn splines, only to discover later that the worn agitator splines caused the new transmission splines to wear out at an accelerated rate. Transmission and Agitator should be replaced together, along with a new Agitator mounting bolt. There are plenty of video's online of how to do this repair so I won't get into that here. Just wanted to drop the above sage advice. Transmissions for these washers aren't cheap.

I watched the supplied video when I purchased the parts

Pulled the agitator, un-screwed the drive hub, cleaned the splines on the transmission, vacuumed the debris out of the tub. The repair video said to put towels or something down in the tub so if you drop a screw it will catch it. Put it back together and re-calibrated it. It didn't want to go into the calibrate mode until i moved the mode switch all the way to the left and then right first. Good quality factory parts!

I couldn't have done the job without the video or a helper. Replacing the first rod was a struggle but once we figured it out, the rest were easy.

Removed belt cover from bottom of the transmission , remove old belt, clean the pulleys ,and re install new belt. The new belt fits tighter so it did a few time to get the belt fully seated. Re install belt cover.

I checked out the reviews and the recommendation of these "professionals", replaced the part easy enough when it came in. However, it didn't solve the problem. Got an actual professional to come in and see what the problem was, and they determined that gear oil was being leaked and it wasn't worth replacing.

Tried to get a refund and return the part. Was told absolutely not. The money back guarantee is a lie.

Watched your videos. Knew I didn’t have the strength to do it myself. Contacted my son, he came by and using your instructions( you made me look very knowledgeable) it was done in short order!

Nothing to it. Just remember to put the insert in the knob, NOT on the selector stem. Line up the flat part of the insert with the flat part of the stem and push the knob in place.

Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicates the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.

My spin cycle was running, but spinning slowly and not drying my clothes. The agitator spun quickly like normal, but the basket did not spin fast. It seemed like something was slipping. I checked the belt, but it seemed fine and it was less than a year old. I was afraid that the transmission was going, but there wasn't any grinding sound of gears. Luckily the hub part description said that this could fix the slow Spin cycle. Over all the repair was easy, but pulling the agitator off was very difficult. I've got a strong grip and patience and after about 10 - 15 mintues of yanking on the agitator it came off. Don't try to use pliers as it will damage the plastic agitator. Replacing the hub drive and reassembly went very smoothly. The old hub drive wore out because it is plastic and connects to the metal drive shaft from the transmission. After years of torque, the hub will eventually strip out. Sooner depending on your usage and heavy duty cycles. In case you don't know, your machine might have the service manual in it on the inside of the body taped to the side. Mine helped me run through some troubleshooting steps and component tests to pinpoint to problem. Thanks Parts Select!

slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys