LAT7334ABL Maytag Washer - Instructions

Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?

First I took the seals out of the box they came in and let them hang on a hanger to get all the kinks out of them for a few days. Then I started at the corners of the refrigerator doors and peeled the old seals off on one door then replaced the seal by using my thumbs pushing at the corners first and once I had all four corners in I worked my way around the rest of the door, After both doors were done I used a hairdryer to expand the seals against the refrigerator case to make sure it seals tight.

Started with removing 4 screws on the top of the control panel. Once open, I found the schematic taped to the top. I traced the wires and found the 2 wires to test. I unplugged them and attached the jumper wire. Turn on machine and it worked. Ordered the part( it came in in about 3 days. First disconnect the power. The micro switch is mounted with 2 screws, remove these and as you disconnect the wires , attach them to the new switch, put it back in place and reattach the screws. Test .

I followed video instructions which were very helpful and getting to the lid switch assembly was not difficult. After putting it on we still had nothing. I noticed there was quite a bit a corrision on the connecters so we cleaned those with fine emery paper, reconnected them and like magic , the washer is back in business. I was very surprised the part arrived about 36 hours after I placed the order and in just a couple of hours at the most we had a working washer again.I've got partselect.com saved in my favorites for any future diy repairs needed.??

Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.

Your web site is amazing Ive enjoyed watching your videos,this is a really great way to see what it takes to repair your washer very informative. Steve was a good teacher for me I just followed along as he explained each step and my washer came apart just like he said. I removed the two front console screws and pulled slightly forward and lifted console up and tilted it back where it was out of the way. next I was able to lift cabinet up from the back and remove it from the frame and lay cabinet on the floor on top of a rug I had to protect the finish on cabinet . Now I had access to the lid switch and simply removed the two screws in the cabinet and the old switch. I connected the two wire connections to the new switch (no)normally open connection, used same actuator the instructions say to do this because the one that comes with the new switch won't fit so use the old one. on my washer there's a cover that fits under this switch and It took me a little longer to get the screws to line up so they fit through the switch and into the cover but It worked fine. Now all I had to do was reinstall the cabinet just like Steve did on the video my only problem with this was seeing where the tabs in the frame were located so that the slots in the cabinet would fit over top of frame tabs I used a flash light in one hand and lowered the cabinet down I held the light on the frame tabs and the slots in cabinet fit right in then lowered cabinet to the rear frame tabs where i just had to push slightly on the sides of cabinet and it fit right in.Next i pushed the back panel in place and on the top of washer just like in video reinstalled both spring clip clamps and the console and reinstalled the two screws. I plugged in the washer put drain hose back in drain pushed washer back in place turned it on working great now ! Thank You so much for your help Dan.

Order replacement lid switch, installed it, good to go. The installation video and instructions with the replacement part were very helpful.

Used duct tape as the video provided instructed and also to hold second hinge lid ball in place. Firmly pushed down on the lid until it easily popped in place.

At first, I suspected the timer. In the problem solving section of the Maytag owner's manual, there was a reference to the Lid Check Switch, which was the queue I needed. with the help of the electrical diagram, I located the switch,then hotwired that circuit to confirm to myself that it was the switch that was faulty. Overall an easy fix.

took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at

I was only missing one of the bumpers but that was in pretty poor shape so I replaced them both. It didn't take much to do. Just pressed the bumper into place and Viola! instant gratification.

I guessed that the lid switch was bad based on internet information that suggested that cause of the problem. I confirmed this by disconnecting 2 wires to switch and taping them together to bypass the switch. Wiring diagram was available. Washer worked that way so I ordered a new switch which arrived within 22 hours, regular shipping.

Replaced the switch. No need for me to add detailed instructions for this simple swap. More than enough descriptions are already collected on the excellent website of this outstanding parts supplier!

>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!

First I removed the front of the washing machine and removed the two bolts that held the top in place. I then replaced the spring. The spring was a little tricky because I had to use a screwdriver to stretch the spring enough to fit.