MAH6700AWM Maytag Washer - Instructions

Disconnected power cord. Shut off water supply. Disconnected hot water supply hose. Removed top cover. Disconnected appliance connection to Hot Water Control Valve. Removed screws holding HWC valve. Removed existing HWC valve. Installed new HWC valve. Reconnected appliance connection. Reconnected water supply hose. Turned on water to check for leaks. Reconnected power supply. Started washer with hot cycle selected. Timed water fill time. Replaced top cover. Washed a load of whites in hot water. Installation and test complete.

Remove back panel disconnect hoses clamps with hands, use socket wrench on hex bolts, remove pump use philip screw driver. Install new pump same tools, replace panel stated washer, works like new.

Of course, before starting any work always make sure your power cord is unplugged to begin with. Move the washing machine to an area with enough room to maneuver around as needed. Now, move around to the back of the washing machine and remove the two Phillip headed screws from the back panel. Push slightly up to pull the two bottom flanges out of their slots. Then pull out on the bottom of the panel which will remove it to allow you access to the inside of the washing machine guts. The drain pump is located directly inside and to the left being held down by three bolts with two hoses running from each side of it. Since there may be a bit of water stored inside the drain pump and hoses have a shop-vac ready to suck up any water that will otherwise go all over the place. If your washer has been down for a while that means sour disgusting mildewed water. Now, unplug the power cord on the top left of the pump and wedge it out of the way making sure it doesn't get wet. Use either a wrench or pliers to remove the three bolts that are holding down the base of the Drain Pump. Remove all of the screws that are holding the Drain Pump to the base. Flip it over to remove the last screw from the bottom. Twist the Drain Pump slightly to move the notches to be able to remove the Drain Pump from the base. Reverse this process to place the new Drain Pump on the base and into the washing machine. If you purchased a Drain Pump with a whole new base already on it then you just have to remove the three bolts and place the new drain and base in. This job is a very easy fix and would have cost you around $300 to $400 dollars having a repair man order the part and come out and do the work. I know because I asked a repair man how much he would charge me for this job. So save your money and fix the easy jobs yourself. Just don't tell my wife it was easy. HaHa!

Figured out the part needed to properly fix the problem and when the part came, I was glad I chose the correct one even though I pretty much knew that it was what I needed. I disassembled the door, took the old/broken part out and put the new one. It took about 20 minutes to do it.

Ordered new pump from Parts Select. Pump arrived within 2 days. Removed back cover off washer, 2 screws. Took 2 hoses off pump. Removed pump bracket and pump, 3 bolts. Took less than 2 minutes to remove old pump off bracket and replace new pump. Put everything back together and machine works great and water is out of clothes. Price of pump was the lowest I could find and I couldn't be happier with Parts Select quick response and price.

I read what others wrote and put two and two together and 15 mins. later I was up and running. lots to take apart but it all went smooth and no left over parts washer runs like new again

I simply followed manufacturers direction from the service manual that I had purchased. I removed the cover from the back of the washer, removed the old belt and put the new belt on. The old belt was certainly stretched and putting the new belt on simply required that I walk the new belt on to the pulley and then adjust the belt to the center of the pully. The end result was a washer that now spins as it did when new.

My husband read on the Internet how common this problem is and how easy we could do it ourselves rather than pay the service etc.... While reading there was a link for Part Select. We simply found the part with-in minutes and ordered. They have PayPal so I basically ordered it in less than 1 minute, emailed my receipt and DONE! We selected overnight shipping because the laundry was piling up - we received the part less than 24 hours and I was up and running before dark! PERFECT!

Removed the front face of washer (broke the plastic pieces on face-no big deal). Had to remove the front housing piece to remove the inner clamp then remove seal. Aligned the new seal up and worked backwards making sure all screws were tightened down. Not super hard, but breaking the plastic pieces wasn't fun.

I ordered the pump because we have 3 kids and laundry piles up. The pump was not the issue, because it would drain in rinse, but not during spin... The computer would have been a $330 part. Not sure the issue, but my wife wanted a new dryer so we replaced the washer at the same time. I didn't use the part. The website was really easy to order and it got here fast.

It is very easy. Unplug from the wall. Take out the two screws from the back that holds on the top panel. Unscrew the three screws inside the door by the latch. Reach inside the washer from the top and unplug the three plugs on the latch part. Then plug in the new part , put the three screws back in. Then put the top panel on. Plug in and magic. It works!

I removed the back service panel and checked the drain hose for any debris and checked the connection from the tub basin to the drain pump. I then check the drain pump and noticed the impeller blades were a bit worn. After the new drain pump arrived, I did have to swap the old intake housing with the new one in order for the whole thing to mount to the shock-absorbing mounting plate. Reconnected both hoses and the electrical connection and everything ran great!

first of all, I am not at all handy, so that fact that I could do this at all is pretty amazing. I watched the video and it was very good. At first all went smoothly...I got the top off, the control panel off and the detergent drawer out. Then I ran into problems, three of the six screws holding on the front panel wouldn't come out. I sprayed Liquid Wrench on, waited for a while, still wouldn't come off, then I tapped them with a hammer, still wouldn't unscrew. But I was able to access the door latch from the top rather than the side...a little tight and awkward, some swearing was required, but it worked. Machine now working like a charm, yay!

Took both the screws out on the top back. Lifted up the back about 1/2 inch and slid to the back. Reached into the front of the washer where the latch was connected. Disconnected the 3 wires (plugs) attached to the latch, took out the 3 screws located inside the washer door. Took a second person just to hold the latch and bring it out after the screws were off the front inside the washer door. Put new latch in, connected the wires, put in the screws behind the washer door (3 of them) and slid the top into place and put the screws in the back. Takes longer to tell you than to do it. Remember the screw on the left side front (top) as you face the washer and remove that screw. The plastic had disintegrated on mine but am not going to replace that part until I have to.

Removed the broker door lever with screwdriver, installed the door lever with screwdriver. Took about 5 minutes.