A212S Maytag Washer - Instructions

The instructions were clear. Did every step. Did 2 loads so far and everything works like new.

The repair was very simple.
1. Shut off water and disconnected the water lines.
2. Removed screws holding water valve bracket to wash machine.
3. Disconnected electrical connections and water fill hose.
Installation was reverse of removal. The directions said to use a small piece of rubber hose that was included in the package, but it was not necessary. Double check for water leaks before finishing installation.

I'm a 70 year old woman. I followed all instructions provided by "Steve" from Partselect video. The video was very well presented and allowed me to fix the leaking problem myself. Watch the video...you can do it.

The water valve on the cold side was making noise when cold water ran. I removed the screens but did not see a problem. I ordered a new valve and installed. The noise is gone and the water flow is back to normal.

At the time we did not realize the water flow had slowed.

This repair started because I wanted to clean the lint build up out the exhaust vent. But when I moved the washer out, the tile floor was buckled from water damage. So I removed the old tiles and coated the cement with waterproof paint and sealed the seams of the baseboards. Then before reinstalling the washer I had to locate the water leak. I looked at the water inlets and the faucets and saw (and felt) nothing wet. Then I started the wash cycle and looked for the drips. I found them on the left side coming from under the unit. I removed the water inlet plumbing (two screws hold it in place) from the back of the washer but there was no leak. Finally I removed the front panel and could see water running down the side and coming from near the top of the machine. This was right behind the water inlet unit and I thought that one of the hoses was leaking. To get to that area I then removed the top casing and found the injector port was leaking, not the hoses. To remove the front panel I had to take out two screws at the bottom of the panel. To remove the top I had to remove 4 screws...the two rear screws were easily accessible but the two front screws were inside the unit and the one on the left had restricted access because of the electrical unit installed there. After the replacement parts arrived it was relatively easy to remove the front and top again to gain access to the injector port. I removed the old nozzle and valve and installed the new parts. Then I started a wash cycle to check that the leak was fixed. The water did not leak so the repair was successful.

Tried the water level control first. didn't fix it.
Then replaced the air tube for tub fill volume.

The thing here is that it didn't have a hole in it nor was it blocked where you couldn't blow through it.
The prolbem was that at the tub end it has a larger diameter and that was nearly filled with softener residue so it changed the air volume.
That reduced air volume caused the air pressure to be wrong to the water level sensor.
My most useful tool was a magnet mount flashligt inside the cabinet so I could see to get the hose back on.

Order the parts needed the washer working ASAP - Three partsf explain several times what I needed - paid extra for express shipping by Fed Ex
took more time then regular US Mail.
When I receive the parts only received two - one the important parts when to a local appliance parts store while waiting for my shipment and completed the repair.
Waiting for a refund and additional shipping cost -very disappointed have use your company along time - that why both Maytags are having their 40th Birthday.

First I had to hold the balls into the little holes on the side of the lid - one at a time- and tap the plastic ball into the side with a small hammer. I did the same with the other side. Silde the lid to match the holes located on the washing machine - give a little push to make sure that the balls are in place. You have your lid fixed to your machine where you can lift the lid and it will stay up without falling.

Note: If the balls fall out - make sure to tap a little harder so that the balls stay in place.

Removed washer tubs inner and outer nut (part # 10 ) on inner was hard to remove and is a reverse thread used hammer to loosen once off removed 1st tub - then removed set screw #17 and then unscrewed mounting s item #29 this again required some hammer tapping to loosen - once off used flat head screwdriver to pry & remove the rubber piece on bottom of outer or 2nd tub -but keep going as the leak will probably be from part #20 tub bearing ( this will save you the time to test and find out it still leaks and have to take apart again after only replacing #29 removed 3 bolts holding tub - disconnected hoses and removed 2nd tub - used rubber hammer to knock out and install #20 tub bearing - reasembled and wow no leaks to cost about $120 - time worked on 3 hrs - only because took apart 2 times - down time on washer 10 days as we didn't order all parts to start with no beer needed but did enjoy a nice red wine - good luck

Removed two screws from bottom of front cover. Raised front cover to disingage clips and remove. Removed two screws to release top cover. Propped top cover up with mop to allow access to injector site. Removed two clamps to free injector sleeve, nozzle and valve from inlet hose. Installed new clamps, sleeve, nozzle and bracket. Lowered top cover and tested for leaks. None found. Reinstalled top cover. Reinstalled front cover. Washer back in service.

First removed the two lower screws from the front panel. I then unscrewed two screws holding the top(lid) of washing machine. I then lifted the lid and let it rest on its rear hinges. The syphon is removed by unscrewing four screws from the rear of the washer. I then cut the original clamp holding the syphon to the hose. New syphon was installed. Enclosed hose clamp was used to tighten around hose. Syphon was then then screwed back to the rear wall of the machine. Easy fix. Water leak solved.

Turn the water supply off. Disconnected the hot and cold hoses from wahing machine. Unplugged the machine from power supply. Removed two screws holding the water inlet valve to the machine frame.
Took the old valve out and marked the wire connectors. Removed the wire connectors and the remaining hose from the old valve. Took the new valve and connected the wires paying attention to the markings made earlier. Uses the little adapter hose which came with the new valve to make the new hose connection on the outlet side of the valve. Put everything back and it worked fine.
These partselect guys are very prompt in sending the things you order. I have used them many times and am very happy to deal with these guys.

It was as simple as leaning the machine back far enough so I could get to the belts - which were on the bottom. The diagrams that came with the ordered parts were right on. This is the first time I have attempted this myself - my repairman has retired - I'm sure I will do it again.

I went to the Internet and saw how to pry the front panel off the washer. This gave me access to the two belts and four pulleys underneath the washer; a pair for the Drive and a pair for the Pump. There was enough slack in the original belts that they came off with minimal effort. The new belts were easy enough to install. It took a mere seconds to install the new Spacers on the Front panel of the cabinet. The most time consuming portion of the project was getting the washer turned out of its tight corner to get access to the clips on the bottom of the front panel.

Followed the procedures recommended for replacement of all the parts included in the Tub Bearing Kit and the Mounting Stem/Tub Seal kit as illustrated in a detailed, 32 minute repair video for the Maytag A606 washer which is available on YouTube. Many difficulties were experienced in the disassembly procedures due to extensive corrosion of tub bearing and tub stem parts (the washer is 47 years old).
I was not successful in using a special tub wrench that was purchased to break loose the old tub mounting stem and its threaded lock nut. The old tub mounting stem, lock nut, and the tub bearing race had to be cut off the threaded support shaft using a saws-all electric tool. Finally, corrosion on the edge of the tub caused problems with water leaks once the tub top and its rubber tub seal ring were reinstalled and the washer was put back into operation. The bottom line is that it may be questionable to attempt major repairs on washers that are 40+ years old and have any extensive corrosion in internal, mechanical parts.