Models
>
WF306LAW
WF306LAW Maytag Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for WF306LAW
Viewing 7 of 7Keep searches simple, eg. "belt" or "pump".
In Stock
$11.80
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
In Stock
In Stock
$181.80
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
In Stock
$95.15
This part helps keep the washer from vigorous shaking during its cycles. They are sold individually. They mount to the front half of the outer tub. Appliance would take 2.
In Stock
In Stock
$261.92
Also known as a bellow. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle.
In Stock
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for WF306LAW
Viewing 5 of 5Lid or door won’t close
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Burning smell
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Leon from North Platte, NE
- Parts Used:
- WP34001260
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
door latch split
replaced door latch but door would not close had to remove latch assembly and reset the latch in the latch assembly. To reset latch in latch assembly you remove the black plastic only on latch assembly then press the spring down with thumb move the black plastic catch back to the latch position. when you remove the black plastic there is
... Read more
four metal switchs and one spring that you have to pay attention too so remove very carefully.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHARLES from MAGNOLIA, TX
- Parts Used:
- WP34001320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
A small coin had entered the impeller and the blades ground off against it.
The rear access is attached with 2 Phillips head screws, which I removed.
The drain hose is held up with a similar screw.
I removed the screw and drained the hose into a bucket.
Then I just removed the connector and hoses with my fingers, removed the three 1/2" bolts holding the pump in place, changed the pump and put every ... Read more thing back together. Works like a champ. Quick and easy fix.
My only negative comment is that I only needed the impeller, but had to buy the complete pump assembly. Other than that, all fine.
The drain hose is held up with a similar screw.
I removed the screw and drained the hose into a bucket.
Then I just removed the connector and hoses with my fingers, removed the three 1/2" bolts holding the pump in place, changed the pump and put every ... Read more thing back together. Works like a champ. Quick and easy fix.
My only negative comment is that I only needed the impeller, but had to buy the complete pump assembly. Other than that, all fine.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cheryl from commerce city, CO
- Parts Used:
- 34001254
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken glass door on front load waher.
Never thought that the glass would break like it did. Removed the whole door assembly and took out the screws that hold the plastic retaining ring for the glass door. Replaced glass and reassembled the door. Very easy repair. Took about 15 min.
Was this instruction helpful to you?
Thank you for voting!