Models
>
XAV13PRBWW
XAV13PRBWW Maytag Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for XAV13PRBWW
Viewing 6 of 6
Keep searches simple, eg. "belt" or "pump".
$99.17
This pump has 2 ports. This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
In Stock
Order now and your part arrives by Apr 26
$10.88
This snubber ring fits washers and is located between the leg and dome assembly. The ring has a diameter of 9 inches. It is used to reduce noise and vibration for stability when the washer is operatin...
In Stock
Order now and your part arrives by Apr 26
Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are NOT available separately - they are ONLY availab...
In Stock
Order now and your part arrives by Apr 26
This washing machine drive belt is used with some clothes washers. This belt is all black in color and is made entirely of rubber.
In Stock
Order now and your part arrives by Apr 26
$7.60
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
In Stock
Order now and your part arrives by Apr 26
In Stock
Order now and your part arrives by Apr 26
This is a multi-use cover screw. It fits appliances such as dryers, ranges, washers, dishwashers, refrigerators, air conditioners, washer dryer combos, freezers, wall ovens, microwaves, dehumidifiers,...
In Stock
Order now and your part arrives by Apr 26
$9.79
This is a replacement lid switch actuating cam for your washer. The cam is located on the underside of the washer lid, near the hinge. The cam actuates the lid switch, so your washer knows the lid is ...
In Stock
Order now and your part arrives by Apr 26
$47.14
This kit includes the lid switch and the plunger. The pin on the lid pushes on the lever of the switch to tell the machine that the lid is closed.
In Stock
Order now and your part arrives by Apr 26
$17.44
This push button is just over three inches long. It is all black in color and is made of plastic.
In Stock
Order now and your part arrives by Apr 26
In Stock
Order now and your part arrives by Apr 26
In Stock
Order now and your part arrives by Apr 26
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for XAV13PRBWW
Viewing 12 of 12Leaking
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Burning smell
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Spins slowly
Fixed by these parts
How to fix it
Shaking and Moving
Fixed by these parts
How to fix it
Spinning Issues
Fixed by these parts
How to fix it
Touchpad does not respond
Fixed by these parts
How to fix it
Lid or door won’t close
Fixed by these parts
How to fix it
Draining Issues
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Boca Raton, FL
- Parts Used:
- WP35-6465
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
washing machine was making alot of noise
I found the water pump bearings were going bad from humidity. I replaced the pump with a new one and it runs quiet again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Hueytown, AL
- Parts Used:
- WP22003483, 12002213
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Washer tub would not spin, pump would empty water from tub.
Lay washer on front, removed belt. Removed center pulley with thrust bearing (pulley was worn on upper end, against thrust bearing, thrust bearing was worn also). Installed new thrust bearing & pulley kit. Cleaned & lubed slots that motor insulators slide in, installed new belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Warminster, PA
- Parts Used:
- WP21001950
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The belt and pulley on the drive motor broke
unplug the washer. Removed the top of the washer by removing the hold scews and tabs on the upper back. Place a scew drive under the front and pry up to release the snap tabs. Then the front panel by removing the two screws on top and lift the panel up to expose the motor at bottom front. Remove the motor cover (plastic)and motor from the
... Read more
base, replace the pulley on the shaft (you may need to break or pry the old pulley off) install the new pulley making sure it is all the way up the shaft locking the tabs into the shat groove. Reinstallmotor to the base. To replace the belt, tilted the unit backwards to access the pulleys from the bottom and installed.
Note: it ios easier to install the belt fully on the two smaller puleys attcahed to the drive motor and pump and then wrap as much as you can around the larger drum pulley. Hold the belt in one hand and turn the drum pulley clockwise with the other and the belt will follow and install. reverse steps to reassemble.
Note: it ios easier to install the belt fully on the two smaller puleys attcahed to the drive motor and pump and then wrap as much as you can around the larger drum pulley. Hold the belt in one hand and turn the drum pulley clockwise with the other and the belt will follow and install. reverse steps to reassemble.
Read less
Was this instruction helpful to you?
Thank you for voting!