LAT9800AGW Maytag Washer - Instructions

Thoroughly cleaned the edges to be sealed with a wire brush and sand paper. shimmed the top piece with 1/4 inch plywood strips. seated the top piece with the seal attached and worked the seal down into place. Positioned the seal clamp, carefully, and tightened the clamp screws. Replacing the seal did the trick, even though the old seal did not look to be in bad shape.

I simply took the old switch out and put in the new one. The part arrived very qickly and the website was super easy to use.
thank you so much!

I looked up the procedure to remove the switch in a repair book, removed the broken switch. Then I reconnected the wire leads, put the part in and closed everything up. The part arrived so quickly and there were even instructions with the part which made the repair go so easily.

Wish there was a video. I am above average handy but this one- I might just pay someone next time...The tape on the threads was a great tip but took a while to understand what they meant by putting tape on the threads. Scraping off the old pads is easy for the front one but the back pad and a half is so hard to reach to really get it cleaned. Bruised and cut knuckles on that one. Then not having the glue for the pads was a surprise and you have to get a good contact type cement that sets in 10-15 minutes or you will be waiting hours to put it back together. It was easy to put the first spring on, then the second and third got harder and harder.

I went to a major appliance part outlet in my area...they told me that they didn't make the parts in the USA anymore. I found your website, ordered the parts, installed them in less than 15 minutes and now the washer works great. I would recommend your website to anyone... thank you

The hardest part was figuring out how to get the front panel off of the washer. Once that was done, the pump came off easy.... 3 screws attached it to the bottom panel and 2 hose had to be disconnected. Putting the new one in was easy.

Determined that the lid switch was not completing the circuit. I then removed the 3 wires from their posts along with the 1 screw and removed the bad switch. Then, in reverse order installed the new switch. The part was 1/3rd the cost of the part sold locally. I ordered the part at 3:15pm Monday afternoon and it arrived at 1:00pm Tuesday- the next day. UNBELEIVABLE SERVICE....!

After I replaced the timer, the washer still would not wash or spin. So my son replaced the lid check switch. It was hard to remove the screw, but he finally managed to remove it and easily replaced the switch. The washer works perfectly. We kept the timer installed (also easy to do by removing the old and replacing it with the new by just unplugging wires and I think one screw) because the old one had not worked properly for a few years when I had a similar problem which resolved, except it would only work in main cycle with soaking which was sufficient for me. This large capacity washer is in good shape and I hope will last at least another 5 - 10 years. ).

removed screws on front of washer, removed bolts holding top cover hinged back, nut driver to remove agitator, slipped agitator off, removed tub hoses, did not have special wrench to remove large nut on shaft, used punch and grinder to removed, had new large nut so wasn't concerned about damaging old one, pay attention to thread pattern to know how to turn, if you had special wrench job would be easier, removed spring bolts and took out inside drum and tub. cleaned corrosion and installed new seals, can be hard to slip on new seal, don't use grease, get dishwashing soap to use as lubricant to put on. Put back together and all is good.

Took front panel off. Ran machine. Pump is see-through. Could not see any "aeration" of the water in the pump and no water was coming out of drain hose. Disconnected electric. Disconnected hose from drum to pump(first emptied ALL water from drom)and drained in bucket. Disconnected drain hose from pump to drain and drained any water. Checked for obstructions in hoses. Removed pump. Checked belt (was fine after 14 years). Ordered new pump. Received the next day! Replaced pump and tighten belt. Connected hoses and test it. All OK. Replace panel and did laundry.

Thinking the water pump was not doing its job in removing all of the water after the rinse cycle, I replaced the water pump.

1. Unplug washing machine.
2. Remove front cover (2 screws).
3. Pull belt and hoses off pump body (watch for water in drain hose!).
4. Remove 3 screws holding pump to bottom pan. 5. Reverse process with new pump.

This job is straighforward, and it helps to have 2 wood blocks to prop up the front of the washer.

Unfortunately, this didn't fix my problem. Actual cause of the water in the tub was a leaking inlet valve (solenoid assy).

Repair went well, but my switch only had one contact on the non common end. The new switch had two contacts. One is for operation with lid open and one for lid closed. Make sure to connect to the lid closed contact and the common on the other end and leave the lid open contact unused.

Your website is wonderful. I read another womans account of how she fixed her machine and then I just followed her instructions...how cool is that!

I looked at the common problems in the owners manual and one item was the lid was not closed or the lid switch was bad. I took off the control panel and there was a schematic inside. This showed 2 lid switches. When trying to see if one switch was closed as it should be, touching the multimeter to the contacts was enough to get the washer going. .

checked lid switch ,plunger stuck in the in position 1 amp fuse blown took switch apart it was full of green copper corrosion stopping plunger from moving correctly. replaced switch and fuse and wow washer works