PAV5057AWW Maytag Washer - Instructions

Using nutdriver or screwdriver, remove metal panel from lower left side of back of washer to expose the pump. This is where the drain hose attaches to the washer. Use pliers to move the clamp off of the drain hose, then ease the hose off of the pump by wiggling it back and forth while pulling gently. Be careful to keep drain hose opening pointed upward until you can point it to a bucket, as there's likely to be quite a bit of water in it. Detach drain hose on other end as well (wiggling / pulling works well here; no clamp is used, so no pliers are required). Install new hose by reversing above steps.

I tilted top cover to remove front washer panel removed suspension springs to remove complete tub assembly to gain access to bottom. Drive pulley to remove snubber ring I performed the repair step by step as per your video. was dead on made the repair go smoothly. I installed the belt last tilting washer mechine back to gain access to undercarrige just walked belt on all three pulleys self adjusting then. made sure washer was level. Front to back side to side no rocking in any deriction My wife did four full loads problems gone I think all needed to be done to complete repair snubber ring , washer drive belt, & leveling machine all played there roll in putting washer back in factory working condition washer not a angery walking vibration nightmare

We followed the instructions show on the video. However, our model was assembled slightly different. We had to remove the screws from both sides of the side panels so that we could remove the tub from inside of the machine. Also our model only has one belt not two.
Over all it was easy considering my husband and I had never attempted to repair a washer. Once we got it back together it when back to working like it had never been broken!
We would have never been able to repair our washer without the video that your site provided... thanks so much!!??

Sure wish the manufactures would consider making the older models again as lots of us are not happy with the new modules being manufactured presently!

Removed the old hoses and screwed on the new hoses.

Got it outside layed it on its side and replaced the motor and belt thinking motor got very hot and heated belt, it was worn from age so replaced it at the same time, hooked water hose up to cold side to test, worked great. Wife very happy

Looked under the symptoms .I had replaced the belt 2 weeks ago, so I ordered the drain pump. Pulled washer away from wall, removed water lines, unplugged electric. I removed the rear panel, found the old part right there, disconnected the in/out tubes, removed old pump, installed the new, re-attached hoses, reinstalled the belt over the 3 pulleys, re-installed access panel. Reconnected water and electric after placing washer back in position. Runs like a new machine!

Pulled up the top of the washer and removed the lid hinge with a star tip screw driver. Realized that I also needed the hinge pins and had to reorder those. They should come as a kit.

Followed directions from video on your site. It was very helpful. The snubber ring fixed the problem.

Studing the numerous notes under the parts listing, help me determine which parts to purchase and replace. These listings also helped me to do the repair with much ease. Once the front and rear panels were removed, I detached the springs which came out very easily. I then pulled out the tub and removed the pulley and loosened the screws holding the snubber which then came out. Put in new snubber tightened screws, replaced pulley & put tub back in place. The springs were a little tougher which led me to believe the old ones were streched. I used a towel to brace tub to one side so as to attach spring on the low side. Used Vice Grip pliers and could not phathom using anything but. Put everything back together and washed a load of towels. The tub was way more stable, but still, towels were little damp. Respun and they dried. Determined that the repairs was all good but told wife not to put so many towels in at once which is probably why the snubber & springs wore out.

We had a repair guy come in and he said fixing the pump would cost at least 250. I called my dad and he walked me through it over the phone. I took off the back of the washer, and laid the washer on it's side. I then had to take a break as I had flooded my kitchen. (Lay the washer at an angle.) The belt was taken off by the repair guy. I then undid the hoses, taking the clips off with pliers. Next I screwed the new pump in, and put the hoses back on. FInally I took the belt and stretched over the two small pullies, and then pulled it to the bottom of the big pullie and started spinning it until it wrapped itself all the way around. It wouldn't have taken over an hour but I had a baby who needed me ever couple of minutes.

We replaced the valve in the washer that feeds the hot and cold water to the wash/rinse cycles. The replacement was not simple only because you have limited space to work in as the back of the machine does not come off other than a small door in the back or by removing the top. We elected to work in the small space but were able to replace the part within a short period of time and the washer is now working again.

I took the washer into the garage, removed access panel from back. Spun drive belt. This located the trouble with the pump. I removed pump with three sheet metal screws and hose clamps. Upon delivery, I notice the two pumps were not identicle. I called Cust Serv. They assured the difference was ok. I installed the new pump with three screw, put the belt and panel and hoses on and ran a test load of my junk clothing. No trouble.

Removed the screws on the back plate pulled the hose clamps off removed the belt and three screws off the pump went back just as easy and the machine was like new again. If only all repairs was this easy!

Turned off the water supply. Removed clothing and bailed out water fro tub. Removed back access panel. Turned washer over to access the bottom and removed drive belt by turning the large pulley attached the drum while pulling the belt over the pulley. Next remove the two hoses attached to the pump, remove the screws holding the pump on and remove the pump. Replace the pump by reversing the procedure, as for replacing the drive belt, place the belt on the motor and pump first and start it on the larger pulley and hold it on while you turn the pulley, it will pull the motor adjustment as you turn and when fully in the pulley it will be properly adjusted. Then replace the access panel, turn the washer upright, push back in place, turn on the water supply and replace the drain hose. Back in business. For me, while I was waiting for the new pump to arrive, I took the time to remove the agitator and tub and give it a good cleaning inside and out, but that's me.

Remove back compartment, remove belt disconnect two water rubber tubes from the drain pump, unscrew three screws securing the drain pump from the frame. Replace with a new drain pump, secure to frame with thee screws, reconnect rubber tubes, and replace belt.