MAT12PDAAW Maytag Washer - Instructions

new replacement water pump leaked where plastic housing upper and lower halves were bonded, presumably with glue. As a quick fix I wrapped pump with some 3M 4411N sealing tape. Seems to have stopped or really slowed leak. I was going to get another new pump but now worried it will leak as well so going to see how long tape fix works..

all went well until testing. tub level did not shut the water off, caused a spill

Followed the directions posted by another user. His tips were very important and helpful. At first we only ordered parts where it was leaking, then decided we might as well change the remaining parts as recommended by the other user in his description. This is the FIRST issue we have had in 19 years of use. Ordered the parts, received them quickly and correctly. Installed them and it works like a new machine. This Maytag will probably last another 19 years.

Removed front door from washer lifted front of washer off floor and removed belt’s put washer back on floor
Removed motor and slide
Cleaned and replaced slides and greased put back in washer secured
Then lifted front of washer back up replaced new belts and started the washer up worked great put front of washer back on done
Great instructions that came with parts

A friend said the cause was probably a belt. On Google we checked the washer model number which took us to your site. We looked at the videos on how to do the repairs, and so ordered a drive belt and pump belt. They arrived in two days. My husband is 84-years-old, I'm 83 -- difficult for us to lift the machine to tilt it. Experimenting with fulcrum and lever, we managed -- that's what took so long. After watching the videos again, I laid on the floor and was able to apply the belts. Washer works great!

Repair not that complicated. Remove front, lean top back, remove agitator, remove special nut, remove inner tub, remove seal. Clean shaft and seal surfaces. It is highly recommended to the spanner wrench to remove the special nut. It appears one can do it with a punch and hammer, but the nut is too tight, and corroded from years of water exposure. I believe part number is TJ90TB123A, about $15. Watch the video on this web site, very good.

Followed the instructions on-line. Pulled the washer out from the wall, tipped it back about 45 deg. & removed the two philips screws as the base of the front of the washer.Removed the old belts which showed little wear, disconnected the hoses from the pump. Replaced the pump which was held in by only 3 nut-head screws, attached the belts & adjusted the tesnion as described on the website.

Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.

watch the video and it was very simple replace belts like they show on the video. lay the washer on it back and the belts was visabile. removed the small belt and then removed large belt, and replace the large belt and small belt. i used no tools. that because i lay the machine on it back.

My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect again. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.

I removed the two screws holding the switch and removed it from the machine. I then removed the broken spring and replaced it with the new one sent to me from partselect.com. I reinstalled the repaired switch and turned on the machine. It was easy as that and it works great. PartSelect.com is the best.

Replaced lid switch, but problem still continued.

We were not sure if the problem was the belts since they were not completely broken or overly worn down, but decided to try to put new ones on given the burning rubber smell and some light smoke coming from beneath the washer when it was on the spin cycle and the drum would not spin. We found some how to videos online and through the part select customer experiences, we ordered the belts and got them within 2 days. We put the new belts on, which is fairly easy and quick to do with the proper tools once you get the front panel of the washer off. The new belts seemed to have done the trick, as the washer began spinning again with no odd sounds or smells once the new belts were installed, and it has been running great so far. I highly recommend ordering from this site, as the parts are the real factory parts and are easy to find an order based on your appliance model. I found the pricing and convenience, as well as knowing the parts would be right and the best quality, to be the best part of this site, as ordering from other online retailers may land you with the wrong parts or kits with parts you don't necessarily need.

I propped up the machine. Turned the water off .took the pump belt off, then took the two hose clamps off. With a bucket and towels on hand for left over water in the hoses, i removed the two hoses. Then removed three screws that held the pump on. Installed the new pump in reverse order.

Unplug washer and shut off water valves. Remove water hoses from the faucets and caught the water in the hoses in a bucket. I removed the drain hose from the back of the washer and caught the water in the bucket. Remove front panel by removing 2-screws at bottom and tilting it out to come off. Disconnected the hoses to the pump and caught most of the water in the bucket.. An old towel stuffed under the bottom pan of the washer, under the pump hole caught most of the rest of the water. Tip the washer on its back and removed the belt coming from the motor. Removed 3-screws that hold the pump on and angled the pulley end through the hole in the bottom of the washer. I just reversed the procedure to install the new pump and everything else. I would have replaced the hoses and belts, but I had just done that about a couple of years ago, when I replaced the connector at the top back of the washer for the hose from the pump and hose to the drain in the wall, that had a crack in it and was leaking.