LAT2000GGE Maytag Washer - Instructions

First I lifted the top of the washer to get access to the screws that held the hinges in place, unscrewed them, removed the broken hinges and put the new ones on, replaced the screws and closed the top. It was very easy. I was amazed that I could still get replacement parts and at such a great price, less than $15.00 with shipping!

The hardest part was finding the model # on the back. I couldn't move the washer out...so used a mirror! I used a putty knife to pop the 2 fasteners securing the top. Tilted it up & proped with a plastic clothes hanger. Unscrewed the one screw which is easy to get to with the top up. Replaced the hinge with the 1 screw. Closed the top. Gave the broken hinge to my wife as an early Mother's Day present.

unscrewed screw holding old actuater in and replaced it whith the new part.

removed rear acess panel and used pliers to remove leaking hose then reinstalled new hose..

Followed the excellent utube instructions you provide. Piece of cake when I followed the video. The rear springs became much more difficult because my model does not have rear access panel. They were the only stuggle. Thank you for doing the repair videos

I unplugged the machine, tipped it back slightly and rested in on a gallon paint can. I inspected the under side and manually advanced the fan belt to hear if I could hear the noise at the water pump. The pump pulley and shaft was worn and there were metal shavins (small) on surface of pulley.

Then I removed the belt from the pulley, rested the machine back to normal position, removed front panel (two sheet metal screws on inside top), removed the water pump hoses (htere is water int he hose & pump assembly so you will get some water on floor.

Then I removed the pump and ordered a new one. The installation was the reverse, machine works like new and the washer tub spins better than ever during the final rinse and spin, since the worn water pump was binding and stressing the machine.

Thanks to Part Select - Your website is awesome and your service instructions and user advice gave me the confidence to do the repair myself. I saved $150 - $250 for the repair.

Removed the front panel to get some light in to the machine. Removed the two hoses connecting the pump to the drain and tub. Removed the three screws holding the old pump in place. Did the reverse to install.
This was a piece of cake.
Thanks for having the parts needed to do this job.
Tom

I took out the agitator first, then I took out the inner tub, next I took out the outer tub, and last I took out the transmission assembly. After replacing the snubber I put the transmission assembly back on, then the new outer tub and next the inner tub. Last I put the agitator back on.

Replacing the pump with the new pump was very easy for me, because of my degree in Mechanical engineering, so I am use to dealing with pumps, engines, gears,etc. However, my wife watched me do the entire job and she is now able to replace this part in the future. The design of the Maytag is very simple to repair, and for that I am very greatful that we can order the parts and do the repairs ourselves withhout having to call a repairman. This was our first problem after 6 years of smooth operations by this washer.

Took off the back plate. Looked to see where it was leaking. Squeezed the clamps on top and bottom to remove from hose and pull hose out.

remmoved the screws on the back that hold the panel on. removed the two hoses attched to the pump. removed three screws and pulled the pump out. spun the pulley and noticed no movement inside. looked closer at the pulley to notice it was broken. ordered new pulley online. received quickly. new part fit exacttly right. put three screws back in. hooked two hoses back up. put belt on pulley. plugged in and worked great.

Removed the inner basket and outer tub to replace the gasket and rubber seal. just had to remove about a dozen screws to get it out.

Tipped the machine up to replace the belt.
The noise didn't go away at first. I decided to spray all the pulleys with some silicone spray, that did the trick.

Disconnect Power. Disconnect supply hoses. Open top by releasing top retainer clips with a thin blade or putty knife. Remove 2 sheet metal screws retaining front cover. Remove front cover. Lay a blanket on the floor and lay the machine over on its side leaving access to the front where the panel was just removed. Take belt off. Remove pump hose at bottom of drum. Prop up drum so it is centered in its normal position and not laying to one side. Do this near the lid end. Remove all centering springs - carefully. Drum and transmission assy will now come out through the front opening. Flip drum assy upside down with transmission up. Loosen the screws (do not remove completely - WARNING OF 200 LBS SPRING LOAD!) that clamp the snubber ring to the transmission. Remove the old snubber ring and replace with new. Be sure it is completely under the flange all the way around. Tighten the retaining ring screws. Reassemble all parts in reverse order. Done. Be sure to level the machine per owners manual instructions.

I changed the piece easily

Disconnect all water supply and unplug washer. Remove 3 screws on back panel of the washer. This will expose the pump unit. Detach belt on the bottom of the washer. Then detach two hoses that connects to the pump unit. Use pliers if necessary to disconnect hoses. Use 5/16 socket with extension to take out three bolts the connect pump to the washer. That's it, now replace old pump unit and with new. Place bolts back in the 3 holes, reattached hoses, cover the back with 3 scres. Connect the belt to the pulley system on the bottom. Connect water supply and plug it in.