MAV7257AWW Maytag Washer - Instructions

first remove drive belt then then remove dust cover on bottom of shaft take 5/16 nut driver to only 4 of the screws off that hold the brake cover on install 4 5/16 screws 1" long in those 4 spots.reomve rest of screws then slowly reomve back out 1" screws to relve spring pressure from brake pad.install all new parts from partsselect.com then install other part taken off in oreder and make your wife very happy

I didn’t have special tool for brake but punch and hammer worked. Seal was easy to replace. Several videos online to show you how. It wasn’t worth it to tear apart the transmission and buy more parts/seals (if they were even available). But I didn’t know how much oil was in it. I drilled a hole in the side to somewhat check level and added 80-90 gear oil. It was almost empty and added almost a quart. Used a self taping screw/bolt with gasket sealer to plug the hole. I got 34 yrs out of this washer. If it fails, oh well. Just hate to buy a new one that only last 10yrs if im lucky.

The replacement was very easy, just one bolt and RR was a snap. However, the first part that came was defective and I called the 800 number, spoke to the rep and the part came the next day. Excellent customer service, and would do business again

Simple remove and replace. Plastic cam and hinges simply snap out, replacement parts snap right back in. Needle nose pliers were helpful to remove broken lid cam. With hinges and lid removed, took advantage of great opportunity to clean lid and and top of washer.

I first took the fabric softener dispenser off and used
a ratchet wrench to take the nut off. I then removed
the agitator, put the new one on and reversed the process. It was extremely easy!

I opened up the top of the washer which exposed the tub, I took the top ring off the tub and under in side of the ring is the seal. Took the old one out and put the new one in. The old seal was completely wore out.
It was real easy.
Finding the part is usually the hardest part, but thanks to Parts Select finding the part was the easiest part of the repair.

I removed the screws to loosen the belt, took off the old belt and put on the new belt. Tightened it up and has been working ever since.

Thank you, Lester

you guys ship faster than anyone else. One day I order the part and a day or two later there it is. :)

Disconnect electricity....remove front panel by gently prying up lid.... Remove two small screws at corners of front panel. You may need small nutdriver here or very small hands, you can easily swivel tub out of the way....once front panel is off water pump is at the bottom right... It is only connected by two squeeze clamps and 3 nuts... This is obviously where the adjustable wrench and nutdriver come in very handy... Otherwise this job will be a bit longer....be prepared for residual water to pour out...you will need towels or a bucket....replace old with new one by reversing the process...at this point tilt the entire washer on it's backside or at least at a 45 degree angle to access the bottom... Swivel the motor away to slack up the belt...remove belt and replace in reverse order of diassembling.... Should take no more than 15 minutes.... Good luck!!!!!

Diconnected water lines, layed washer on its side, spun pulleys and pulled belt off at the same time, put the belt on in the same way. VERY simple

Replace the motor in 25 minutes, my repair guy said it was not worth the time , I got this motor for less than $150. And save my self over $600.00, this was incredible.

I knew it was the belt because of all the noise it was making. I ordered the belt and it arrived real fast. I pulled the washer away from the wall and tipped it back at about a 45 degree angle against the wall so I could get under it. I propped it with a bucket. I then pulled the old belt off and spun the new one on. Real fast & easy.

take a butter knife and pop the clips loose on the front between the lid and the front take the two screws loose on the front in each corner remove the front cover and you will see the hose take the clamps off and replace the hose

Took a putty knife and raised the top,then took two bolts out, then pulled front panel off. Took hose off from the tub to the pump,and put the new one on. It's working fine.

unpluged the machine , turned off the water .
removed as much water i could by hand ,with pan & towels .
Removed the front panel , tip machine on back feet & prop up .
removed belt from under the machine , take the drain hose off pump , remove pump .
installed new pump , rehook hoses , install new belt & motor pivot spring .
put front back on lower machine turn water back o
n , and plug back in .

Use a blade to pop off the fabric softener dispenser cup. Use socket and extension to unscrew the single hex bolt that attaches the assembly to the shaft. Lift off the assembly and recover the flat washer. Install the new assembly over the shaft and install the original hex bolt and washer. Tighten firmly. Snap the dispenser cup back in place.