PAV3300AGW Maytag Washer - Instructions

disconected water lines unplug power and took drain pipe off, used putty knife to open top of washer and pulled off front removed pannel off back pannel, disconnected water level tube,using vise grips took off springs and pulled tb out used 5/16 socket to loosen screws just enough to pull snubber ring out replaced with new one reversed prosses in putting it back to geather

We had a repair guy come in and he said fixing the pump would cost at least 250. I called my dad and he walked me through it over the phone. I took off the back of the washer, and laid the washer on it's side. I then had to take a break as I had flooded my kitchen. (Lay the washer at an angle.) The belt was taken off by the repair guy. I then undid the hoses, taking the clips off with pliers. Next I screwed the new pump in, and put the hoses back on. FInally I took the belt and stretched over the two small pullies, and then pulled it to the bottom of the big pullie and started spinning it until it wrapped itself all the way around. It wouldn't have taken over an hour but I had a baby who needed me ever couple of minutes.

Studing the numerous notes under the parts listing, help me determine which parts to purchase and replace. These listings also helped me to do the repair with much ease. Once the front and rear panels were removed, I detached the springs which came out very easily. I then pulled out the tub and removed the pulley and loosened the screws holding the snubber which then came out. Put in new snubber tightened screws, replaced pulley & put tub back in place. The springs were a little tougher which led me to believe the old ones were streched. I used a towel to brace tub to one side so as to attach spring on the low side. Used Vice Grip pliers and could not phathom using anything but. Put everything back together and washed a load of towels. The tub was way more stable, but still, towels were little damp. Respun and they dried. Determined that the repairs was all good but told wife not to put so many towels in at once which is probably why the snubber & springs wore out.

Followed directions from video on your site. It was very helpful. The snubber ring fixed the problem.

I took the washer into the garage, removed access panel from back. Spun drive belt. This located the trouble with the pump. I removed pump with three sheet metal screws and hose clamps. Upon delivery, I notice the two pumps were not identicle. I called Cust Serv. They assured the difference was ok. I installed the new pump with three screw, put the belt and panel and hoses on and ran a test load of my junk clothing. No trouble.

Hving read some of the tips in regards to this repair I set out with equal parts of confidence & apprehension. The advice of shifting the tub toward the hinge to be removed is in itself the key to the whole procedure. After having done so & wedging a dust pan handle between the tub & frame to first one side & then the other, I removed the entire lid with the hinge & hinge pin assys. attached as ther is not sufficient clearance to slide a servicable hinge pin from a hinge when only one hinge has beeen removed. With the lid completely removed access to the hinge pin(s) is straight forward. I suggest screwing & unscrewing the fastening screw into a new hinge assy before mounting the hinge onto the machine & also using an offset philips screwdriver or ,as I did, a 1/4" drv. ratchet with a #2 philips apex bit which allows for a better feel & more control over the upside down blind operation of removing & replacing the fastening screw into the hinge assy. Hope this helps. Tom

followed video instructions

unscrewed screw holding old actuater in and replaced it whith the new part.

The hardest part was finding the model # on the back. I couldn't move the washer out...so used a mirror! I used a putty knife to pop the 2 fasteners securing the top. Tilted it up & proped with a plastic clothes hanger. Unscrewed the one screw which is easy to get to with the top up. Replaced the hinge with the 1 screw. Closed the top. Gave the broken hinge to my wife as an early Mother's Day present.

I first had to take the old part out to find out what the part number was. Then I went online and ordered the part. Once the part came in I attached to part and replaced the drive belt. I did not think it could be so easy.

First I lifted the top of the washer to get access to the screws that held the hinges in place, unscrewed them, removed the broken hinges and put the new ones on, replaced the screws and closed the top. It was very easy. I was amazed that I could still get replacement parts and at such a great price, less than $15.00 with shipping!

I followed the video you have on web site. Very good and easy to follow.

Actually I got on YouTube and looked up the problem and watch the short video of it and went from there and it showed me how to take everything apart what the problems were and as I did take it apart and found out it was exactly what they said I simply reversed it just ordered the parts and put them in and took my time to make sure that everything was to specs as I've measured the clearance of the break and said all the hardware back in place it was quite simple yet it was just time consuming took me about two and a half hours but it runs quiet spins great just like a brand new one I couldn't be more pleased with it and I saved quite a bit of money doing it myself

Unlike most videos, mine had a solid frame, no access panels. Following, is my disassembly & repair: I disconnected the water supply lines and drain hose. I slid the washer out into the center of the garage & removed the 9 base screws from the base plate. I slid the frame away from the base, leaving the working parts exposed. After pulling the working mechanisms from the outer frame, I turned it (drum, transmission & base) upside down. I used a pair of vise grips, pinched them onto each spring & removed them, using a downward motion it was a lot easier. I placed the base plate aside, removed 3 opposing screws holding the snubber ring & put 3 longer 8-32 screws in to hold the brake assembly. Then I removed the 3 remaining screws, lifted the plate & replaced the ring. Then I reversed the process, replacing the old springs with new ones & finished the job in about 2 hours.

I pretty much followed the video,and read some of the other comments on how to do it. I only had one problem, the back panel had an opening of about 14"x14" to access the 2 rear balance springs. I finally laid the machine on it's face,so I didn't have to kneel down.The only problem with that,is the tub falls forward, making the springs farther away from the upper hole to attach/stretch, the springs to remove/install. I cured that problem by cutting a wedge out of a piece of 2x4, and stuck it between the top edge of the tub & upper frame. Worked great,held the tub in position, closer to the springs & locating holes. Taking them off is no problem,installing them, was made easier by using the wedge. The parts were a perfect fit, no more 'walking away from the wall' now! Thanks PartSelect