MAH14PDCBQ Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- DONNA from WALKER, WV
- Parts Used:
- 12002533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
washer was leaking water all over the place
removed the door &the top took the tightener off the bellow took old one out put new one on and clean all parts and put it back together works like a new one love it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Truc from San Diego, CA
- Parts Used:
- 12001788
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
broken drive belt
My first time attempted to repair washer and step by step video instruction attached with order confirmation did it for me. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Landenberg, PA
- Parts Used:
- 12002533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
leaky door seal
removed front panel. removed brakets holding top. lifted top hinged backward. Removed tension spring and cable that secures the seal to the drum. Pulled seal out. Put new seal back in. Secured with cable and spring. Reassembled top and front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Crawford, CO
- Parts Used:
- WP22002119
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Washer would not run, seemed like the wax motor was the most common cause.
Watched the video, worked just like shown so as quick as you can take out 8 screws you can make the repair. Turned out it was the MCB but maybe this part (wax motor) Will save a main control board failure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Oak Ridge, TN
- Parts Used:
- 12001788
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench set
washer smelled hot on spin cycle
Replaced the belt and motor isolators. Watching your video made it very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Parma, OH
- Parts Used:
- WP22003262
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
leak in tub to pump hose
removed front of washer. loosened two hose clamps. replaced hose. tightened clamps. replaced front cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Davis from Sacramento, CA
- Parts Used:
- 12002533
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
door boot seal broke
I am happy when PartSelect included the instruction video, so I completed my repair that easy. Thanks the PartSelect. Davis Dao
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lauraine from Kimberling City, MO
- Parts Used:
- 12001788
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Started smelling rubber burning during spin cycle
I thought for sure the washer was toast! Thankfully, due to your website it was an easy 26.00 fix. Husband took care of the repair in about a half an hour. He did not encounter any problems with the fix and it's running like a charm!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- E T from Milton, WI
- Parts Used:
- WP22002162
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Would not enter spin cycle. Found WAX Motor not cycling, 120VAC present when disconnected. Applied 120VAC dierectly cycled OK.
When I found the WAX motor would not cycle I applied 120VAC directly to the WAX motor and machine went into SPIN CYCLE as it should have. Stopped machine and ordered replacement Machine Control Board. Replaced the part and machine works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- scott from lafayette, CO
- Parts Used:
- WP22002119
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Whenever the timer hit the rinse cycle, my breaker would trip
First I took off the door and the front of the washing machine. Then, took off the bracket of the soap dispensing bin from the top of the machine. Then lift up the top of the machine, and unscrew the bracket that holds the wax motots, label and pull wires, replace motors and wires and put back together. This is also a good time to clean and dust the interior of the machine. Before replacing, my motor smelled and looked burnt out, instead of paying $300 -$400 to have someone look at it, I investigated and I fixed it for around $30. I hope I get to inspire people to figure things out and save some cash!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ryan from Troy, OH
- Parts Used:
- WP22003059
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
washing machine leaked out the bottom.
diagnosed problem (hole in drainage pump). unplugged, took service panel off rear, removed hoses, twisted pump counter clockwise. dropped new pump in, made connections, and it was good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Sewickley, PA
- Parts Used:
- 12002533
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Water leaking from the rubber front door seal.
I follwoed the detailed instructions provided via the Part Select web page and instructional video. This information was very helpful. I printed the step by step paper instructions and had them available at the washer. They were very easy to understand. By doing this work myself I saved a $100.00 repair service call and installation cost and another $30.00 on parts. This resulted $130.00 ++ savings and 30 minutes of my time. Thanks for the great help and guidance!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Slinger, WI
- Parts Used:
- WP22003262
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
We had a leak in the tub pump hose
It was very easy...we ordered the part and it only took a day and a half and it was here.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARILYN from SULLIVAN, OH
- Parts Used:
- WP22002162, WP22002119
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
wouldn't spin out all of the water.
Replaced parts then the door wouldn't unlock, so we called a repair man and he's replacing the control board and the wireing harness, it cost 394.85 but the machine is in good shape so it was cheaper than buying a new washer and dryer, because I want them to match & the dryers only 7 years old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from El Cerrito, CA
- Parts Used:
- WP22002119
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Would not go into spin mode
Removed 4 screws and door, lowered and removed front panel,removed screws holding locking tabs for the machine top, removed the four screws holding soap reservoir, lifted the top. Located under the lid and above the doorway I pulled out the wax motor retaineing clip with pliers and the wax motor, used pliers to remove the wire connectors, hooked them up to the new part and reassembled.
Was this instruction helpful to you?
Thank you for voting!